Bedienungsanleitung Indesit K3G2 (Seite 4 von 12) (Englisch)

72079

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

 the mains cable is wired directly into a 13 amp

cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

! For appliances with a rating greater than 13 amp

(eg: electric hob, double ovens and freestanding

electric cookers etc.) the mains cable must be wired

into a cooker output point with a rating of 45 amp. In

this case the cable is not supplied.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket. Instructions for

connecting cable to an alternative plug:

! The wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

If the colours of the wires in the mains lead do not

correspond with the coloured markings identifying

the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E

or or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted

with a 13 amp fuse. A 15 amp plug must be

protected by a 15 amp fuse, either in the plug or

adaptor or at the distribution board. If you are in any

doubt about the electrical supply to your machine,

consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN AND YELLOW EARTH (E)

Disposing of the appliance

When disposing of the appliance please remove the

plug by cutting the mains cable as close as

possible to the plug body and dispose of it as

described above.

Checking the

connection for leaks

When the installation process is complete, check

the hose fittings for leaks using a soapy solution.

Never use a flame.

Adapting to different types of gas

It is possible to adapt the appliance to a type of gas

other than the default type (this is indicated on the

rating label on the cover).

Adapting the hob

Replacing the nozzles for the hob burners:

1. Remove the hob grids and

slide the burners off their

seats.

2. Unscrew the nozzles using

a 7 mm socket spanner (see

figure), and replace them with

nozzles suited to the new type

of gas (see Burner and nozzle

specifications table).

3. Replace all the components by following the

above instructions in reverse.

Adjusting the hob burners minimum setting:

1. Turn the tap to the minimum position.

2. Remove the knob and adjust the regulatory

screw, which is positioned inside or next to the tap

pin, until the flame is small but steady.

 If the appliance is connected to a liquid gas

supply, the regulatory screw must be fastened as

tightly as possible.

3. While the burner is alight, quickly change the position

of the knob from minimum to maximum and vice versa

several times, checking that the flame is not

extinguished.

GREEN &

YELLOW

BROWN

BLUE

13 amp fuse

CROSS-BAR

CORD GRIP

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Indesit K3G2 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Indesit K3G2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info