Bedienungsanleitung Intek RP-600 (Seite 1 von 4) (Englisch)

647632

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

RP-600

DUAL BAND PMR 446 / LPD 433 UHF FM VOICE PAGER

OPERATING MANUAL

INTRODUCTION

This product has been specifically designed for the following purposes :

- as a Voice Pager in Tourists Guided Tours

- as a Voice Pager in Conferences, Meetings, etc.

- as a Voice Pager in traditional Paging Systems (in stores, hotels, restaurants, resorts, factories, warehouses, offices, shops,

etc.) and wherever a same message from a main transmitter must be received by either one or more groups of persons or by

a single person.

The pager operates in the PMR-446 (8 channels) and LPD-433 (69 channels) UHF FM bands. 38 CTCSS codes, call vibration

alert, earset or built-in speaker and more features are included. Band, channel and all other functions are fully programmable by

the system manager in the PROGRAM mode. Please read the following operating instructions before using the radio.

KEYS AND CONTROLS

1. Earset / Charge Jack

2. Holes for Necklace

3. UP Key

4. DOWN Key

5. Built-in Speaker

6. Desk Charger Contacts

7. MENU / Monitor Key

8. ON-OFF Key

9. Backlighted LCD

LCD DISPLAY

A. Channel Number or

Volume Level

B. CTCSS Code Number

C. BUSY Icon

D. Vibrator Alert Icon

E. Keypad Lock Icon

F. CALL Alarm Icon

G. Battery Level Indicator

BATTERY INSTALLATION

1. Remove the locking screw (12).

2. Remove the Belt Clip (10)

3. Slide down and remove the

battery door (11).

4. Install 2 x AA size batteries.

Please respect correct polarity.

5. Re-install the battery door (11).

6. Re-install the Belt Clip (10)

7. Re-install the locking screw (12).

BATTERY CHARGING / 230VAC WALL ADAPTOR CHARGER (Mod. AC-600)

When the battery capacity is low, the Battery Level Indicator (G) blinks. Recharge batteries at this time. When the battery capacity

is low, switch OFF the pager and connect the wall charger to the CHARGE jack (1), then plug it to a 230VAC outlet ; the Battery

Level Indicator bars (G) will blink indicating that the wall charger is connected to the pager and that the charging process is

running. To obtain the maximum performance from the batteries, recharge them only when they are fully discharged. The

approximate charging time with 2 x 1500 mAh Ni-MH batteries is 8-12 hours, depending on the batteries condition. When the

charging time has expired, unplug the wall charger from the AC outlet and then disconnect it from the pager.

BATTERY CHARGING / MULTIPLE DESK CHARGER (Mod. MDC-600)

Please refer to the instruction manual supplied with the Multiple Desk Charger.

WARNING !

1. If the product will not be used for a long period of time, please take out the batteries.

2. Please dispose of old or defective batteries in a safe and environmentally friendly manner.

3. Do not dispose of batteries in fire.

4. Do not recharge batteries for more than 12 hours, to avoid overcharge or overheating, which could damage the radio.

5. Do never try to recharge alkaline batteries, as this might cause damage to the radio or explosion of the batteries.

6. Do not use chargers or accessories others than the original ones, otherwise damage to the radio may occur.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intek RP-600 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info