Bedienungsanleitung Interlogix NXG-1820-EUR Touch Screen (Seite 5 von 6) (Englisch)

629286

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

P/N 230444 • REV A • ISS 01SEP15 5 / 6

Performing Additional Functions

To Bypass Zones

The zone bypass menu is used to bypass (isolate) selected

zones in your security system. A bypassed zone is not capable

of activating an alarm, as it is temporarily disabled from your

system.

This option is commonly used to bypass zones that you wish to

temporarily add to your “stay mode”. Whilst still offering

security on the remaining zones, bypassing zones lowers your

level of security. All bypassed zones will reset and unbypass

when your security system is next disarmed. Your security

system must be disarmed (turned off) before being able to

bypass zones. After bypassing the selected zones, your

security system must be armed (turned on in either the away or

stay mode to secure the remaining zones.

1. Enter a valid PIN code to unlock the screen.

2. Touch MENU.

3. Enter a valid PIN followed by ENTER.

4. Touch Security – Zones.

5. Touch the zone number you wish to bypass, if you do not

know the zone number press the List View button to see

the zone names.

6. Touch Bypass.

7. Touch Back to select more zones to bypass.

8. Touch Home to finish.

To Unbypass Zones

1. Enter a valid PIN code to unlock the screen.

2. Touch MENU.

3. Enter a valid PIN followed by ENTER.

4. Touch Security – Zones.

5. Touch the zone number you wish to unbypass. Currently

bypassed zones will be in *blue*. If you do not know the

zone number, press the List View button to see the zone

names.

6. Touch Bypass.

7. Touch Back to select more zones to bypass.

8. Touch Home to finish.

Set up Zone Chime Mode Feature

You can setup your keypad so that it will beep when selected

zones are tripped or activated − this is called chime.

Chime mode can be enabled or disabled for each individual

zone and does not trigger any alarms. In this case it is only

used as a low level alert such as a customer entry door.

The zones you have selected to be in the “chime group” are

stored in memory and are not cleared when the security

system is armed and disarmed.

1. Enter a valid PIN code to unlock the screen.

2. Touch MENU.

3. Enter a valid PIN followed by ENTER.

4. Touch Security – Zones.

5. Touch the zone number you want to add to chime mode, if

you do not know the zone number press the List View

button to see the zone names.

6. Touch Chime.

7. Touch Back to select more zones to add to chime mode.

8. Touch Home to finish.

Specifications

Compatibility xGen Security System

Voltage 12.0-13.5 VDC (provided by panel)

Current

170 mA max with sounder and screen on

max brightness,

40 mA in idle mode

Screen Resistive touch 3.5” colour TFT LCD screen

Capacity 512 zones, 96 areas, 644 outputs, 256

users

Wiring xGen 4-wire bus

Code combinations

4 digits

(There are no invalid code combinations.)

10 000

Dimensions (W × H × D) 82 mm x 125 mm x 18 mm

Housing Opal white with silver frame

Weight 125 g

Operating temperature 0° to 49°C

(32° to 120°F)

Storage temperature −34° to 60°C

(−30° to 120°F)

Relative humidity up to 90% noncondensing

Regulatory information

Manufacturer Placed on the market by:

UTC Fire & Security Americas Corporation, Inc.

3211 Progress Drive, Lincolnton, NC, 28092, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, Netherlands

FCC compliance

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference when the

equipment is operated in a commercial

environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

You are cautioned that any changes or

modifications not expressly approved by the party

responsible for compliance could void the user's

authority to operate the equipment.

NFPA 72

Check local ordinances, this device is not listed

by an approved test lab to meet NFPA 72 and

therefore may not be sold or installed for use with

a fire system in some localities.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Interlogix NXG-1820-EUR Touch Screen Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info