Bedienungsanleitung Intex 28206 (Seite 9 von 13) (Englisch)

752321

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

87A

SAVE THESE INSTRUCTIONS

English

(87IO) METAL FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 06/04/2019

Page 9

The last joint connection may be difficult to complete. You can

do it though, if you first simultaneously raise the last joint and

beam about 2 inches (5 cm). Now insert the beam into the joint

while lowering the pieces into position. The beam will easily

slide into the joint (see drawing 2.3). Ensure that the last joint

is fully connected before proceeding to connecting the legs.

3. Vertical legs assembly

• Attach the leg’s end cap (4) to the bottom of each leg (7) first.

With the beams and T-joints assembly resting on the ground, slide

one vertical leg into the belt loop located in the middle of the pool

liner and insert the top of the leg into the bottom of the T-joint (3)

(see drawing 3.1). Continue the process with all the vertical legs.

• Lift the beams assembly and make sure all the legs are in a vertical

position

(see drawing 3.2). Push all the T-joints downward to

ensure they are firmly connected to the legs.

• Pull gently, in an outward direction, the bottom of the leg making

sure the leg is vertical and perpendicular to the level ground.

4. Filling of the pool

• The following applies to pool liners with hose connectors (16’ (488 cm) & below pools). If the pool was

purchased without a filter pump, insert two of the three plugs (10) into the black filter pump outlets. Do

this from the inside of the pool so that water will not run out when filling it. If the pool was purchased

with a filter pump, read the Krystal Clear™ Filter Pump Manual first and then proceed to next installation

step.

• Before filling the pool with water, ensure that the drain plug inside the pool is closed and that the drain

cap on the outside is screwed on tightly. Fill the pool with no more than 1 inch (2.5 cm) of water. Check

to see whether the water is level.

IMPORTANT: If the water in the pool flows to one side, the pool is not completely level. Setting

up the pool on unlevel ground will cause the pool to tilt resulting in the sidewall material bulging

and a potential collapse of the pool. If the pool is not completely level, you must drain the pool,

level the area or move the pool to a different area that is level, and re-fill the pool, following the

above directions.

• Smooth out the bottom liner wrinkles (from inside the pool) by pushing out where the pool floor and pool

sides meet. Or, (from outside pool) reach under the side of the pool, grasp the pool floor and pull in an

outward direction. If the ground cloth is causing the wrinkles, have 2 people pull from opposite sides to

remove all wrinkles. Use the properly assembled pool ladder when entering or exiting the pool during this

process. Also make sure all the legs are vertical and perpendicular to the ground.

• Fill the pool with water up to just below the sleeve line.

(see drawing 4).

POOL SETUP (continued)

WATER LEVEL

3.2

3.1

2.3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex 28206 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex 28206

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info