Bedienungsanleitung Intex 633T Krystal Clear (Seite 13 von 16) (Englisch)

587286

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

(109) MODEL 633T FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/21/2013

109

SAVE THESE INSTRUCTIONS

English

Page 13

TROUBLESHOOTING GUIDE

IMPORTANT

If you continue to experience difficulty, please contact our Consumer Service Department

for assistance. See separate “Authorized Service Centers” sheet.

• Filter cord must be plugged into a 3 wire

outlet that is protected by a Class A

Ground Fault Circuit Interrupter.

• Reset circuit breaker. If circuit breaker trips

repeatedly, your electrical system may

have a defect. Turn off circuit breaker and

call an electrician to correct the problem.

• Let motor cool down.

• Adjust the chlorine and pH level. Consult your local

swimming pool supply stores.

• Clean or replace cartridge.

• Check the cartridge for holes. Replace if damaged.

• Operate the filter for longer periods.

• Clean the strainer screen at the inlet.

• Clear any obstructions in the intake hose by

discharging it inside pool wall.

• Tighten hose nuts, check hoses for damage, check

pool water level.

• Clean cartridge more often.

• Clean inside the plunger valve.

• Pull valve handle to full upright position.

• Install the nozzle at the upper position of pool inlet,

and the strainer at the lower position of pool outlet.

• Turn off pump, clear any debris or obstruction in the

outlet, remove all air from the filter pump and turn

pump on again.

• Turn off pump, if water leaking from the vacuum

release valve, then release valve needs to be

replaced. Contact Intex Service Center immediately

to order replacement. You may cover release valve

with the cap temporarily if you ensure that the strainer

cover / strainer grid is installed and you Do Not run

the pump while pool is occupied.

• Fill pool to correct water level.

• Clean strainer screens at pool inlet.

• Tighten hose nuts, check hose for damage.

• Clear any sticks or leaves in the intake hose.

• Turn and pull valve handle to full upright position.

• Remove cover & check for O-ring.

• Tighten cover or valve (Manually).

• Tighten or reinstall hose nut.

• Put the o-ring back into the groove.

• Replacea new hose.

• Open air release valve, wait until water starts to flow

out of the valves, then close it.

• The lower position of pool outlet connects to filter

pump water inlet. The upper position of pool inlet

connects to filter pump water outlet.

FILTER MOTOR

FAILS TO START

FILTER DOESN’T

CLEAN POOL

FILTER DOESN’T

PUMP WATER OR

THE WATER FLOW IS

VERY SLOW

PUMP DOESN’T

WORK

TOP COVER

LEAKING

HOSE LEAKING

AIR LOCK

• The motor is not plugged in.

• The GFCI circuit breaker

is tripped.

• Motor too hot and overload

protection shut motor off.

• Improper chlorine or pH levels.

• Filter cartridge is dirty.

• Damaged cartridge.

• Excessively dirty pool.

• The strainer screen is restricting

the water flow.

• Clogged inlet or discharge.

• An air leak on the intake line.

• Scale or buildup on cartridge.

• Excessively dirty pool.

• Dirty filter cartridge.

• The nozzle and strainer

connection are reversed.

• The vacuum release valve

on the plunger valve is

activated.

• The vacuum release valve

on the plunger valve is

leaking.

• Low water level.

• Strainer screen plugged up.

• An air leak on the intake hose.

• Faulty motor or the impeller is jammed.

• An air lock inside the cartridge chamber.

• O-ring missing.

• Cover or air release valve are not tight.

• Hose nuts are not well-fitted.

• Hose o-ring dislodged when

connecting the hose.

• Hose broken.

• There’s air trapped in the

pump housing and inlet hose.

• The inlet and outlet hoses

connection are reversed.

TROUBLE CAUSE SOLUTION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex 633T Krystal Clear Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info