Bedienungsanleitung Inventum BC18 (Seite 33 von 36) (Deutsch, Englisch, Holländisch, Französisch)

54538

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

detectable, the cuff is pumped up again and the cuff

pressure is increased further. As soon as a heart rate is

detected, the heart rate symbol is displayed.

• Heart rate, systolic and diastolic blood pressure are

displayed.

• You can interrupt measurement at any time by pressing the

“START/STOP” button.

• The “ ” icon appears if it has not been possible to

perform the measurement properly. Observe the section

in these instructions on Error messages and repeat the

measurement.

Cardiac arrhythmia

This instrument can identify possible heart rhythm

disturbance during measurement and if necessary indicates

the measurement with the icon .

This may be an indicator for arrhythmia. Arrhythmia is a

condition where the heart rhythm is abnormal as a result of

defects in the bioelectrical system controlling the heart

beat. The symptoms (omitted or premature heart beats,

slow or excessively fast heart rate) may be caused, among

other things, by heart disease, age, physical predisposition,

excessive use of stimulants, stress or lack of sleep.

Arrhythmia can only be ascertained through examination by

your doctor. Repeat the measurement if the icon is

displayed after the measurement. Please note that you

should rest for 5 minutes between measurements and not

talk or move during the measurement. If the icon

appears often, please contact your doctor. Any self-diagnosis

and treatment based on the test results may be dangerous.

It is vital to follow your doctor‘s instructions.

Doctor’s Function

After a successful measurement, the instrument rst shows

the test result. The set limit values are compared with the

test result and shown as follows:

• systolic value within and below the limit value:

value appears

• diastoli value within and below the limit value:

value appears

• systolic value above the limit value: value ashes

• diastolic value above the limit value: value ashes

If you would like to check your set limit values, press the

“MODE” button. You can return to the results display at any

time by releasing the “MODE” button. Pressing the “START/

STOP” button allows you to start a new measurement. Please

ensure that the 5 minutes’ rest between two measurements

is adhered to. If you do not press any button, the instrument

automatically switches off after one minute.

• The results of each successful measurement are stored

together with date and time. With more than 30 items of

measured data, the earliest items of data measured are

lost.

• In order to retrieve measurement results again, press

the button “MEMORY”. Using the buttons “down” or

“up” select the required user memory and press the

“MEMORY” button. Initially, the average value of all stored

results in this user memory is displayed (memory space

8 | EVALUATING RESULTS

9 | SAVING, RETRIEVING AND DELETING

RESULTS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum BC18 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info