Bedienungsanleitung Inventum IOV6032D (Seite 26 von 30) (Englisch, Holländisch)

616223

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

THE FITTING OF THE APPLIANCE

• Check that the cabinet and the space for the oven meet the dimension and ventilation requirements.

• Slide the oven into the cabinet. Make sure the housing of the oven does not come in contact with the walls of the kitchen cabinet.

Make sure there is at least 2 mm between the oven casing and the walls of the kitchen cabinet. Make sure the oven is centered

between the walls of the kitchen cabinet. Note: Make sure the cable is not stuck and does not lie on top of the oven.

• Open the oven door and insert the bushings, provided, in the holes on the front.

• Use the provided screws to fasten the bushings to the cabinet. Take care not to over tighten and break the bushing.

• Close the oven door and plug the appliance in.

• The oven is now ready for use.

ELECTRICAL CONNECTION

Check that the voltage in your home corresponds with the voltage printed on the appliance.

These groups in the meter must be secured with at least 16 amps each. The connection cable must have a cross-section of at least

2.5mm² and must have a length of at least 1.5 m. When the cable is too short, you have no room to already connect the oven and place

it against the wall before plugging it in.

INSTALLATION DIMENSIONS

In the drawing below, all the dimensions are displayed in mm. Make sure you use the right drawing for the model you have.

26 • English

installation instructions

• The safety during use can only be guaranteed when the hob is installed correctly and according to the regulations. The installer is

responsible for any damage caused by a faulty installation.

• The electrical connection must be made by a qualiﬁed electricien. This person is aware of the national and local regulations the

installation must comply with.

• The appliance falls under protection class III and can only be used in combination with a grounding conductor connection. The

manufacturer accepts no responsibility for any malfunction or damage caused by incorrect electrical installations.

• The appliance must be connected to a ﬁxed installation and the means of disconnecting it from the ﬁxed installation must be

installed according to the installation instructions.

• The connection cable must hang freely. Do not tie the power cable or pass it along sharp edges. It must be positioned so that it

does not touch any of the hot parts of the oven.

• The connection point, the wall socket and/or plug must always be accessible.

• The cabinet into which the oven is ﬁtted, must be heat resistant (> 75°C).

• Ensure that the cabinet into which the oven is installed is secure. For example, by mounting it to the adjoining elements.

• Damage caused by incorrect connection, incorrect use or incorrect ﬁtting is not covered by the guarantee.

Attention: any change to the appliance’s interior, including ﬁtting and changing the power cable, must only be performed by a

qualiﬁed electricien.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum IOV6032D Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info