498510
5
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
5
SET-UP
1. Connect POWER SCAN to your computer’s USB port with the included USB cable.
Note: The first time you connect POWER SCAN to your computer, wait a few seconds until you
see a dialog box that says "Found New Hardware" (this means the computer recognizes
POWER SCAN). After you see this, POWER SCAN is ready to use.
2. Insert your appropriate holder and film.
a. If you are scanning a slide, insert it into the FILM
HOLDER SLOT on the top of the device.
b. If you are scanning a strip of negatives, insert the
included strip film guide into the FILM HOLDER SLOT on
the top of the device. Then insert one end of the negative
strip into the FILM HOLDER SLOT on the right side of the
device. Turn the FILM FEEDER WHEEL
counterclockwise while gently "feeding" the negative into
the slot. (If you want to go back to a previous frame or if
the negative strip is getting jammed, turn the FILM
FEEDER WHEEL clockwise while gently pulling the
negative from the slot.)
Note: The negative strip itself must be at least three
frames long. Otherwise, it may get stuck in the device. If
a negative strip becomes jammed in the device, you can loosen it by inserting the included
film retrieval strip into the FILM HOLDER SLOT.
Note: Handle negatives with care. Any dust, scratches or fingerprints will show up on your
saved images. If possible use cotton gloves when handling negatives. It is recommended
to use compressed air to remove any dust on the negatives. This is not included with the
film scanner but can be purchased from an office or electronics supply retailer.
c. If you are scanning a single negative frame, insert it into the included single frame holder
and insert it into the FILM HOLDER SLOT on the top of the device.
d. In the event that films are not able to get out from the film scanner, insert the film retrieval
strip into the scanner, and use it as a tool to retriever the film out by feeding it into the
device.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Ion POWERSCAN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Ion POWERSCAN

Ion POWERSCAN Kurzanleitung - Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch - 28 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info