Bedienungsanleitung Irobot Verro 300 Series (Seite 30 von 31) (Englisch)

632874

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

How Verro Works

iRobot Verro uses a powerful motor to

draw 80 gallons of water per minute

through the ﬁlter bag. This creates strong

suction at two inlet ports under the

robot that draws dirt and debris, such as

bacteria, algae, leaves, and even coins

into the ﬁlter bag where they are trapped.

The pump motor also drives two high-

pressure jets under the robot that loosen

dirt and attached particles, which are

then vacuumed up.

Verro uses the force of the water being

pumped through the robot to hold itself

against the surface it is cleaning and to

move along it.

Each time it changes direction, Verro

automatically alters it course slightly so

that it covers the entire bottom and sides

of the pool efﬁciently.

iRobot

Verro

™

model 300 Quick Start Guide

Instructional photos available at www.irobot.com/usetips

Tip

Clean the ﬁlter bag regularly. Verro uses

the force of the water pumped through

its ﬁlter bag to move properly. If the

ﬁlter bag is not kept clean, Verro will

not move or clean properly.

Tip

Store Verro in a dry place out of direct

sunlight at a temperature between

50 and 104 degrees Fahrenheit. The

Power Supply is water resistant, but not

waterproof and may be damaged by rain.

Important: Failure to properly store Verro

will result in loss of warranty.

Tip

iRobot recommends using the mesh

ﬁlter bag (included) when

the pool contains a signiﬁcant quantity

of large debris (leaves, etc.), such

as when the pool is opened for the

season. The ﬁne ﬁlter bag is ideal for

ﬁltering small debris (algae, sand,

etc.) and for regular maintenance.

Tip

Periodically straighten the ﬂoating

power cord with the Detangler.

Tip

Verro’s Power Supply has an automatic

timer that shuts Verro OFF after

approximately two hours of operation.

When this happens, the power switch

will remain ON. To start another

cleaning cycle, switch the Power

Supply OFF and then back ON and

then press the reset button.

Uncoil the ﬂoating power cord and spread it over the surface of the water, ensuring that it is not tangled

or kinked.

Set the time control dial to 30 seconds.

Place Verro upside down in the pool and rock it from side to side to allow air to escape. Turn Verro over

and allow it to sink to the bottom of the pool so that the wheels rest on the bottom of the pool.

Warning: A Ground Fault Current Interrupter (GFCI) must be installed to

protect your electric outlet and prevent any possible electric shock.

Turn the Power Supply switch ON then press the reset button. The light on the Power Supply will

illuminate and Verro will start to clean your pool.

Place the Power Supply in a dry area at least 3.5 meters/12 feet from the pool.

3.5m/12ft

Ensure that the Power Supply is at least 12 feet from the pool and that the power switch is OFF. Plug

the Power Supply into a GFCI outlet. Ensure the electric outlet has been properly grounded.

Never leave the Power Supply plugged in when Verro is not in use

Plug the ﬂoating power cord into the Power Supply. Be sure not to force the plug as it will only

go in one way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irobot Verro 300 Series Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info