Bedienungsanleitung Irox HELVET-X (Seite 11 von 12) (Deutsch, Englisch, Französisch, Italienisch)

578910

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

~P.11~

(E)

Very Weak Weak Medium Strong

[ ] button

Increases the value of a setting

Enable or disable the alarm when in Alarm display mode

[ ] button

Decreases the value of a setting

Activates manual synchanization for radio frequency

[ RESET ] button (inside battery compartment)

To activate system reset during abnormal condition.

B. DCF77 Radio Controlled Clock

The radio-controlled time is calculated by the Cesium Atomic clock of Braunschweig

(official clock of Germany). Then the time is coded and transmitted from Mainflingen

- near Frankfurt - via a signal on DCF-77 (77.5 kHz). The transmitting range of the

signal is 1500 km, which means that most of Western and Central Europe is covered

by this signal. Within this range the received time is completely accurate. Once sensor

signal(s) are received, the wave icon will flash to indicate that the receiving unit starts

to receive the DCF radio controlled time signal.

Radio Controlled wave icon can indicate 4 levels of signal status:

Once the time signal is received, the wave icon will stay on the LCD, and time and

calendar will automatically be updated.

Note: During 10 minutes of time signal reception, all manual settings will be sus-

pended. If setting is desired, press once [ ] key to deactivate the reception. You can

also press and hold the same key for 3 seconds to manually activate the reception in

normal mode.

C. Setting the clock, multi language, calendar, and temperature unit

1. Press & hold [MODE] button for 2 seconds. 12Hr/24Hr is blinking.

2. Use [ ] or [ ] button to select 12 or 24 hour format, then press [MODE] button to

confirm.

3. The hour digits will blink. Use [ ] or [ ] button to set the required time (each press

the button will increase or decrease the digits by one. Holding the button will cause

the setting to change rapidly). Press [MODE] button to confirm.

4. The minute digits will blink. Repeat the same procedures to enter minutes, Year

(range from 2005 to 2099),Date/Month or Month/Date format, current Month or Date

(Weekday auto selection), languages and °C or °F selection.

D. Setting the alarm

1. Press [ALARM] button once to switch from clock mode to display the alarm time, press

again to switch back to clock time display

2. Press [ALARM] button to display alarm time. Press & hold [ALARM] button 2 seconds

to enter alarm setting mode. The hour digit will blink.

3. Use [ ] or [ ] button to set the desired hour. Press [ALARM] button to confirm.

4. The minute digit will blink. Use [ ] or [ ] button to adjust minutes, and press [ALARM]

button to confirm.

5. The “%” bell icon will be shown to indicate the displayed alarm time is enable.

6. When the alarm is beeping, press [SNOOZE/LIGHT] button once to temporarily stop

the alarm for 10 minutes.

7. Press any button to stop the alarm (except [SNOOZE/LIGHT] button).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irox HELVET-X Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info