579065
15
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
15
- In a dry and cold climate it may take a while for the transmitted values to become stable. This problem will resolve
itself as soon as you begin to sweat from physical activity.
- Incorrect or missing transmission of data can be caused by the following:
- The chest belt has insufficient contact with the body (skin is too dry or chest belt does not fit correctly)
- Weak or empty batteries in the chest belt or in the watch
- Your heart rate is under 30 beats per minute
- Electro magnetic disturbances in the area (transformer station, electrical overland lines, thermionic screens
from PCs and TVs, electric motors, in the car etc.)
- Please note that the transmission distance of approximately 60 cm from a transmitter belt of a person in
your immediate area can also be received on your watch. The overlapping of the signal from your belt and
the foreign belt usually leads to very high monitored rates. This is also possible with chest belts from other
brands! A bit of extra distance between you and the other person or wearing the watch on the other wrist
usually solves this problem.
- High amounts of chlorine in swimming pools and the salt content in sea water can, because of increased
conductivity, affect monitoring.
10. ALARM MODE
Use C to enter Alarm mode.
* Mode prompt “ALRM” is displayed first.
- There are 2 daily alarms and they can be set to refer to Normal Time (indicated by T1) or Dual Time (indicated
by T2).
- Daily alarm sounds at the same time each day, while it is turned on.
- The alarm sounds at the preset time for about 20 seconds, or until you stop it by pressing any button.
- The alarm on indicator is only displayed at the time mode that the alarm is set to refer to.
- Hourly chime sounds at every full hour, while it is turned on.
* If chime is turned on, confirmation sound will be given whenever a button is pressed.
To switch between alarm 1 and alarm 2
Press B to switch between alarm 1 (indicated by AL-1) and alarm 2 (indicated by AL-2).
To set alarm time and turn chime on and off
1. Hold down D until the hour digits start to flash on the display, which indicates the setting screen.
2. Use A (+) and B (-) to change the setting. Holding down either button scrolls the setting at high speed.
3. Press C to advance to the next setting as in the following:
C
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Irox XL P wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Irox XL P

Irox XL P Bedienungsanleitung - Deutsch - 16 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info