Bedienungsanleitung Jablotron AC-814 (Seite 2 von 2) (Englisch)

554823

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

AC-8014/814 receiver 2 / 2 MJQ51505

Enrollment of thermostats

For each channel of the receiver, a thermostat can be enrolled in the

following way:

• Repeatedly press button < or > (left, right arrow) to select the

desired channel (the current channel will be indicated by its LED

flashing).

• Insert batteries into the thermostat. When powered up, the

thermostat generates an enrollment signal and its code is stored in

the selected receiver channel’s memory.

• Digital bus thermostats can be enrolled by pressing and holding

their button for 5 seconds.

• Enrollment of a thermostat is confirmed by the constant lighting of

the green LED.

Only one thermostat can be enrolled to each channel. A thermostat

can be enrolled to multiple channels or other receivers without any

restrictions (it allows the control of several zones by one thermostat). If

you try to enroll a new thermostat to an occupied channel, the new

thermostat will be stored and the former one will be deleted.

Note: Enrollment codes are stored in non-volatile memory, so power

disconnection will not erase them.

Deleting a thermostat

To delete an existing thermostat:

• Using buttons < and > select the desired channel (the current

channel will be indicated by its LED flashing)

• Press the RES button, the corresponding LED will turn off and the

thermostat is deleted.

Indicators 1–14

Indicators on the front housing of the receiver indicate the status of

the output channels.

LEDs 1 to 14 Meaning

Off Channel is not used (no thermostat is enrolled)

Steady Green Channel has a thermostat enrolled, relay is off

Steady Red Relay is on (activated by the enrolled thermostat)

Flashing Green Communication with the enrolled thermostat is down

(Low battery in thermostat, radio interference etc.)

Flashing Red Enrollment mode (to enroll a thermostat)

Flashing Red

(rapidly)

Output is overloaded or short-circuited.

Using the MODE channel / SUM input

The receiver has a special MODE channel to which a JA-8x control

panel (PgX output) or RC-8x remote controls can be enrolled as well

as detectors of type JA-80M. The SUM terminal has the same function

for wired control. This channel can be used for remotely controlling the

mode in which all the outputs will work, switching between two

possibilities: 1) The outputs may be controlled by thermostat signals

demanding/stopping heating 2) The outputs are disabled, but will

respond to freezing alert signals demanding heating. The status of this

channel is shown by the MODE indicator.

Repeatedly press button < or > (left, right arrow) to select the MODE

channel (the current channel will be indicated by its LED flashing, in

this case aim for the MODE LED) and transmit the enrollment signal.

Enrollment of the transmitter is confirmed by the constant lighting of

the green MODE LED.

If no transmitter is enrolled to the MODE channel, then outputs 1-14

react in a normal way to signals from their corresponding thermostats.

If a control panel is enrolled and the PgX output is activated (MODE

indicator lit red) outputs 1–14 react in a normal way to signals from

their corresponding thermostats.

If the PgX output is deactivated (MODE indicator lit green), then

outputs 1–14 are deactivated. They can only be activated in response

to economy temperature signals from a TP-8x thermostat.

MODE indicator

Off

The MODE channel is not used – no transmitter is

enrolled (receiver reacts to standard signals from

thermostats)

Steady

Green

A transmitter is enrolled – the MODE channel is

deactivated, (SUM is active)

Outputs 1–14 only react to the economy temperature

signals from thermostats

Steady Red

A transmitter is enrolled – the MODE channel is

activated

Outputs 1–14 react to standard signals from

thermostats

Flashing

Green

Communication with the enrolled transmitter is down

(Low battery in transmitter, radio interference etc.)

Use and maintenance

All enrolled transmitters (thermostats and detectors) transmit regular

check signals. If the receiver does not receive the signal of an enrolled

transmitter for a certain period, it will indicate that communication with

this device is down (flashing green LED) and the corresponding output

will turn the heating on for 5 minutes every single hour.

One reason for the lost connection can be low batteries in the

transmitter. The average lifetime of a thermostat’s batteries is about

1 year (JA-8x detectors 3 years). Each transmitter checks its battery

conditions and signals in advance if the batteries are reaching a

critically low state (see the transmitter manual for details).

Another reason for possible connection failure can be radio signal

interference in the operational band of the receiver. In such a case the

receiver will usually indicate loss of communication with a multiple

number of transmitters. In this situation, check if there is any non-

approved or faulty radio-communicating device within the range of the

receiver.

If outputs 1–14 have not been activated for 7 days they will switch on

for 5 minutes to protect connected devices. This is also valid for the

output relay provided by the built-in AC-8000R module thus providing

protection for pumps which can be damaged if they are not used for a

long time. However, this feature is disabled for the boiler connection

established by an additional AC-8000R module.

Warning: the manufacturer is not responsible for any damage caused

by improper installation or any non-suitable use of this product.

Specifications

Power supply: 230 V AC, 50Hz, protection class II

Consumption: 0.02 A stand-by; 0.2 A max.

Max. power supply load 1.7A

Internal load-protection safety fuse F 3.15 A

Max. relay output load: 10 A / 230V

Voltage of outputs 1–14 and COM: 24V DC

Max. load of outputs 1–14: max. 0.4 A per single output

and 1.7A total for all outputs

Radio frequency: 868 MHz

Communication range 100 m (open area)

Dimensions: 258 x 214 x 77 mm

Mechanical resistance: IK08 according to EN 50102

Radio characteristics: ETSI EN 300220

EMC: EN 50130-4, EN 55022

Safety: EN 60950

Enclosure: IP30 (EN 60529)

Operational temperature: -10 to +40

Can be operated according to ERC REC 70-03

JABLOTRON ALARMS a.s. hereby declares that the

AC-8014/AC-814 is in compliance with the essential

requirements and other relevant provisions of Directive

1999/5/EC. The original of the conformity assessment can

be found on the web site www.jablotron.com

, Technical

Support section.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the manufacturer after use.

Jablotron AC-814 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info