Bedienungsanleitung Jablotron AC-82 (Seite 1 von 2) (Englisch)

554862

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The AC-82 wireless relay output module MJT51202

The AC-82 wireless relay output module

The AC-82 is a component of Jablotron’s Oasis JA-80 system. It is

mains-powered (230V AC) and it provides 2 relays which can be

controlled by radio signals and offers the following:

• Remotely controllable relay outputs which follow JA-80 control

panel programmable PG outputs

• Remote control of appliances using RC-8x controllers

• Relay output of JA-8x wireless detectors

• Relay output of TP-8x wireless thermostats

RADIO

max F 5 A / 250V

buttons

LEDs

fuse

max 5 A

Installation

Installation of this module shall only be undertaken by technicians holding a

certificate issued by an authorized distributor..

Warning: this device is galvanically connected to the mains.

Open the module’s cover (1 screw) and take out the circuit board (2

tabs). Install the back part of the housing to the desired place, re-install

the circuit board, connect the wires and enroll the desired wireless

devices.

Terminals

L,N Power: 230V AC/50Hz

COM Common terminal for the output contacts X and Y (fused by a 5

Amp fuse)

RE1 Normally open relay X contact

RE2 Normally open relay Y contact

The enrollment of transmitters

The X and Y relays are totally independent. Jablotron Oasis devices with

transmitters can be enrolled to them individually using the X and Y enrollment

buttons. Each relay offers 4 different enrollment modes (1 to 4, see the following

table). The reaction of a relay to a transmitter signal depends on which

enrollment mode the transmitting device has been enrolled to.

Enrollment procedure

• Use the X or Y button depending on which relay you want to enroll a device

to.

• Repeatedly press the relevant X or Y button to select the desired

enrollment mode 1 to 4 as indicated by the flashing of corresponding LEDs 1

to 4 (see the table for guidance on choosing the right enrollment mode).

• Activate the transmitter while the LED is flashing, as follows:

o key fob – press a button

o detector or thermostat – connect its battery up (if it has already been

connected, first disconnect it, and then wait 10 seconds)

o Control panel PG output – key in 299 in service mode

• Enrollment is confirmed by a short flash from all the AC-82 indicators

• If no enrollment signal has been received within 10 sec., enrollment mode

automatically ends.

• If you wish to enroll another device, repeat the above enrollment procedure.

Notes:

• If a device does not enroll, either it is too far from the receiver, or there is

another device already enrolled which cannot be combined with the new

one, or the maximum number of devices has been exceeded.

• Each device can have its own individual reaction (it is possible to combine

different reactions for a single relay = enrolling different devices in different

enrollment modes to the same relay).

• The relay always performs the last received instruction (e.g. if the relay is

already on and a signal for a 2 minute pulse is received, the relay will stay

on for another 2 minutes and then it will turn off).

• Each transmitting device (keyfob, detector, control panel, etc.) can be

enrolled to an unlimited number of different receivers.

• Devices are enrolled to a non-volatile memory, so the AC-82 will not forget

them if its power is disconnected

Use with RC-8x remote controllers

• Up to 60 remote controllers can be enrolled to each relay.

• To operate garage door or parking gate actuators, use the 1 sec. pulse

mode and connect the NC relay contact to the push button input of the

actuator unit.

Use with JA-8x wireless detectors

• Detectors can be enrolled to pulse modes 1 and 2 (up to 60 detectors to each

relay). The 2 minute mode is suitable for automatically switching on lights,

ventilators etc.

• If a detector(s) is enrolled in mode 3, then the relay will be switched if the

detector’s tamper sensor is triggered. In this mode up to 8 detectors can be

enrolled to a single relay (which will be switched if any of the detectors is

tampered with), but no other kind of device can be enrolled, only detectors.

• If a detector(s) is enrolled in mode 4, then the relay triggers if the detector’s

No. Reaction Device Enrollment method

Max.

number

Notes

keyfob button pressing

1 1 sec. pulse

detector connecting battery up

• key fobs and detectors can be combined

• the relay stays on 1sec, turns off and is then ready to be activated again (the pulse is not

extended if another 1 sec. pulse activation signal is received while the relay is still on)

keyfob button pressing

2 2 min. pulse

detector connecting battery up

• key fobs and detectors can be combined

• if another 2min. activation signal is received while the relay is on for 2 min., then the relay

stays on 2 min. more (the 2 minute pulse is extended if re-activated during the pulse)

Latch keyfob button pressing 60

Tamper = on detector connecting battery up 8

• impossible to combine keyfobs with detectors

• * latch = on – off – on – off….

• Tamper = on= relay turns on when a detector’s tamper sensor is triggered.

keyfob

button pressing enrolls

a pair of buttons

• impossible to combine key fobs with detectors or with a control panel PG output

PG output of

control panel

entry of 299 in Service

mode

• impossible to combine PG output with detectors or with keyfobs

On / off

thermostat connecting battery up 8

• can be combined with keyfobs, detectors and a control panel PG output

Triggering = on detector connecting battery up 8

• impossible to combine detectors with keyfobs or with a control panel PG output

Jablotron AC-82 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info