Bedienungsanleitung Jablotron CA-1802 - Athos GSM RESET 3 (Seite 3 von 5) (Englisch)

555042

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM pager CA-1802 „Athos“ 3/5 MHF57402

1.1 Configuration table - be careful to put spaces between words in SMSes (e.g. MASTER RESET 3).

SIM entry* SMS instruction Text Description

RESET EN 3

(After which, the

entry is erased

from the SIM)

MASTER RESET EN 3 Mode setting. RESET 3 = GSM pager for cars with an installed car alarm. Performing the RESET

instruction is indicated by 4 beeps. Consequently, all settings, enrolled remote controllers and wireless

detectors will be erased.

Not applicable MASTER UC uuuu

User code setting – the code allows you to operate the GSM pager remotely via SMS from

unauthorized phones. uuuu is a new user code, 4 to 8 letters (A–Z & 0–9, case insensitive). Factory

default user code is USER

Not applicable MASTER MC xxxx Master code setting –xxxx is a new master code (A–Z & 0–9, case insensitive). The code allows you

to change the maintenance settings for the GSM pager. Factory default master code is MASTER

TEL1 xx...x MASTER TEL1 xx...x

TEL2 xx...x MASTER TEL2 xx...x

TEL3 xx...x MASTER TEL3 xx...x

TEL4 xx...x MASTER TEL4 xx...x

Setting of phone numbers to report alarms to (these phones will also be authorized to control the

alarm via SMS without a user password)

E.g.: MASTER TEL2 +420602123456 will enter the phone number into memory TEL2

MASTER TEL3 0 will erase the memory TEL3.

DIAL1 xx...x

MASTER DIAL1 xx...x

DIAL2 xx...x

MASTER DIAL2 xx...x

DIALA xx...x

MASTER DIALA xx...x

DIALB xx...x

MASTER DIALB xx...x

Setting the phone numbers to dial using Hands free.

E.g.: MASTER DIAL2 +420602123456 will assign the number to the

button of the remote

controller. MASTER DIAL2 0 will erase the number assigned to the

button.

Not applicable MASTER LEARN RC Enrollment of RC-8x controllers - up to 4 controllers can be enrolled, turn the ignition key on before

sending the instruction. To enroll controllers, press and hold buttons

and together for 3

seconds. After you have enrolled all remote controls, turn the ignition key off. By enrolling the first

controller all other controllers previously enrolled will be erased. All the desired controllers should be enrolled in

a single enrollment session.

DIP abcdefghij MASTER DIP

abcdefghij

DIP parameter entry – see the DIP table

SET abcdefghij MASTER SET

abcdefghij

SET parameter entry – see the SET table

TELU xx...x MASTER TELU xx...x SIM card validity maintenance call setting (for pre-paid cards) 1x month the xx..x number is called,

call duration 10 s to maintain the validity of SIM cards requiring this.

Not applicable MASTER TXT 01,text

Modifying SMS messages and instructions (see chapter 9.1). The maximum length of a single text

is 30 characters. Information texts (with indices starting at 27) can be modified using the user code

USER (optional). To change instruction texts (indexed by 01 to 26) the MASTER installation code is

always necessary.

*It is not possible to modify access codes or SMS texts, or to enroll controllers or detectors by storing numbers in the SIM card phone directory

Always use CAPITAL letters when writing into the SIM card!!!

6. DIP parameters

Parameters A to J correspond to DIP switches. Setting is performed by

the SMS command: MASTER DIP ABCDEFGHIJ

Description

DIP

0 1

A Not applicable for this mode (a “0” can be entered).

B Silent alarm

Audible alarm

SMS alarm report only

SMS alarm report and siren sound

phone call

D SMS remote control not

confirmed by SMS reply

SMS remote control instructions

confirmed by SMS reply

E Not applicable for this mode (a “0” can be entered).

F Not applicable for this mode (a “0” can be entered).

User can not change SMS

Texts

User can change SMS texts by TXT

Sequence

H Not applicable for this mode (a “0” can be entered).

I Enter 2 for the immobilization by an SMS. No other option is

available for a GSM pager.

Self-location disabled

The car’s location will be sent by

SMS after an IMO instruction has

been performed.

Factory default setting is DIP 1111000000 (bold letters in the text).

7. SET parameters

Parameters A to J correspond to SET switches. Setting is performed by

the SMS command: MASTER SET ABCDEFGHIJ

Description

SET

0 1

A Not applicable for this mode (a “0” can be entered).

B Not applicable for this mode (a “0” can be entered).

C Not applicable for this mode (a “0” can be entered).

Instant activation input:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

E INP1 logic:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

F Not applicable for this mode (a “0” can be entered).

G Not applicable for this mode (a “0” can be entered).

H Not applicable for this mode (a “0” can be entered).

Do not turn off the GSM

module automatically.

Turn the GSM module off after

30 minutes of inactivity.

J 0 = AUX output is a bus for communication with CR-11A modules

1 = AUX output provides power for external sensors

Factory default setting is DIP 1001111101 (bold letters in the text).

If you want to change only particular DIP or SET parameters, enter x for the others.

8. SMS control from an authorized phone

Text SMS Description

IMO

STOP (immobilize) the vehicle (after turning ignition key off)

UNIMO

Unblock (mobilize) the vehicle

STATUS

Reply with status information, e.g. GSM pager reports:

Time: 27.01.04 13:04, Status: Armed, Unblocked, Ignition

of“.

HELP

The car alarm will reply with a brief list of SMS instructions.

UC xxxx

To change the user code. xxxx is the new user code, 4 to 8

characters (A –Z & 0 – 9). Factory default user code is

USER

CREDIT

parameter

To obtain the balance of a prepaid SIM card if used. See

12.3 for details

AUX

parameter

To operate CR-11A output relays as well as the appliances

or circuits that are connected to these relays (see par. 13)

HF abcdef

Hands-free set adjustment:

a – enable calls (0= disabled, 1=enabled)

b – auto answer incoming calls (0= disabled, 1=enabled)

c – microphone sensitivity 0 to 9, (5)

d – speaker volume 0 to 9, (5)

e - ringing tone volume 0=mute to 9= max., (5)

f – ringing sound 0 to 9, (1)

SIREN

To activate the siren for 30 seconds

 The instruction must contain spaces (e.g. HF 105551).

 If an SMS instruction is sent from an unauthorized phone, it is

necessary to put a user code before the instruction (default is USER).

Again, a space is necessary. Example: USER IMO

 SMS instructions are not case-sensitive. Only basic ASCII can be used

in the SMS instruction texts.

 If the SMS text contains the % sign, then the following text will be

ignored. Characters %% in the message stop processing the

following text. Using these characters is suitable when sending an

Jablotron CA-1802 - Athos GSM RESET 3 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron CA-1802 - Athos GSM RESET 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info