Bedienungsanleitung Jablotron CA-322 Accent (Seite 2 von 2) (Englisch)

555049

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Immobilizer CA-322 „Accent“ 2 / 2 MDF532 05

antenna

+12V

ignition

key (15)

turn

indicators

remote control

(max. 3x)

battery

12V

3x immobilization contacts

(3x max. 15 A)

1413

1314

dome

light

door switches

trunk switch

central

locking

LED indicator

push button

VALET

CA-322

main unit

132

456

unlock

lock

el. powered

windows

AL1 input

Immobilizer CA-322 „Accent“ - operating instructions

Arming

After switching off the ignition, removing your key and exiting the

vehicle, close all the doors (closing of all windows is also

recommended). ARM the immobilizer by pressing the button (A or

B) on the remote control.

One flash from the turn lights confirms arming and the LED

starts to flash. At the same time the immobilizer is blocked and the

doors should automatically lock (if equipped with central-door

locks). If a powered window control system is also connected to the

„lock“ signal, all the windows will be closed automatically* when button A is

used for arming (button B arming does not have any influence on the

windows).

Disarming

To disarm the immobilizer press a button (either A or B) on the remote control

once.

The turn lights should flash twice. At the same time the doors should unlock

(if equipped with central-door locks) and the LED should turn off. When you

open a door the dome light will come on for 60 seconds or until you switch on

ignition key.

REARM* - if you do not enter the car within one minute after disarming, the

immobilizer will rearm and lock the doors automatically again.

AUTOIMMO* will block the car automatically if the ignition key is turned off for

more than 5 minutes. This immobilization (doors stay unlocked) is indicated by

intermittent LED light. The immobilization can be switched off by a remote control

button (A or B). It will also switch off if you switch on the ignition key and press

the VALET button /*. Automatic immobilization can also be temporarily disabled

if you switch off the ignition key while the VALET button is pressed. The

AUTOIMMO function will be disabled until the remote control is activated

again. This can be used, for example, when you leave your car in a car shop

for maintenance without the remote control.

Emergency Disarming*

If you lost your remote control, perform following: Open the car door, switch on

the ignition key and press the hidden VALET switch.

Note: If emergency disarming was disabled in setting mode, there is no way to

disarm the immobilizer (call service).

No reaction of Immobilizer to remote control

If there was any attempt to scan the remote control code (or while rare, as

may happen after the remote control battery has been replaced) then the

immobilizer will not respond to the signal from the remote control. In this case

the system asks you for a confirmation of control code validity.

To provide, make Emergency Disarming (if armed), switch on the ignition

key and press the button of the remote control (A or B). After that the remote

control should work as usual (if not, go to service).

Note: this way your system performs more complicated analyses of coding

system. It insures your immobilizer is secure from outside interference and the

remote control is indeed yours.

Maintenance

There is no special maintenance required. If the distance from your car at

which the system can be operated continuously decreases, then replace the

remote control battery (after releasing of a screw on the rear side of remote

control housing; mind the battery polarity). A suitable replacement battery is

L1016 (6VDC). Usual good battery life time is one year.

We recommend a yearly professional inspection of the immobilizer. Periodic

inspections should be made to the door switches.

We recommend installer to give a detail explanation of „Accent“ functions

to the customer after installation, to avoid problems and misunderstandings in

future.

* these functions are selectable in setting mode

Examples of „Accent“ use for different central locking systems

If your locking system needs another kind of control signal than negative

pulses, install a couple of over-switching relays to the Accent outputs (or you can

use CR-2 relay unit). See following diagrams for different locking systems.

System with positive control inputs:

Pneumatic central locking system:

Program duration of output pulses 2 or 4 seconds according to the reaction

time of the pneumatic system.

Simplified additional installation of central locking system:

When

manual operation of the whole system from the driver's door is not requested,

you can use the following easy solution. Install two-wires actuator (recommended

type CM-2) to each door of your car. Connect them as shown in the following

diagram. Program duration of Accent output pulses 0.3 seconds. This way all

actuators are operated with the remote control.

When necessary, the door locks can also be operated manually with a key

(the same way as before the central locking installation).

Caution : In this case do not use longer locking signal !

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron CA-322 Accent Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info