Bedienungsanleitung Jablotron GD-04 (Seite 5 von 15) (Englisch)

554882

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

GD-04 DAVID 5 MKS51202_OS1*

7. David is not case sensitive (does not distinguish between lowercase and UPPERCASE

letters).

8. The use of accented characters is not recommended.

9. After an SMS message has been received, David switches off both the X and Y relays.

10. See table 1 for a brief instruction list.

7. Remote operation via SMS instructions

When using texts which have been programmed for David SMS operation (relay control, status

interrogation) the following conditions apply:

• David does not distinguish between authorized and unauthorized phones when processing

operational SMS instructions. Instructions can be sent from any phones, but the texts must match the

texts which have been pre-programmed (except the lowercase/UPPERCASE attribute).

• Access codes are NOT part of operational SMSes.

• A single SMS message can contain multiple instructions separated by commas, e.g.

HEATING ON, LIGHTS OFF, STATUS

• David can be so configured that every instruction performance is reported by SMS.

• Received SMSes with unrecognised instructions can be forwarded to the so called service

number (see table 1).

• If you are not sure whether any other text will be automatically added to the SMS on its way to David

(for example, when using an SMS internet gate) type the message like this: %instructions%%.

Example: The SMS text “1/1 www: %heating on%%” is interpreted as heating on.

8. Remote operation via dialling-in

David allows you to control the X and Y relays via dialling-in from pre-authorised phones. If a

call is made to David from a pre-programmed number, the call is rejected and the relay reacts as

follows:

o If a limit is set to the relay switch-on period then the relay switches on for the limit period.

o If no limit is set (zero value is set for the limit) then the relay switches on permanently -

until a switch-off SMS instruction or another dialling-in event occurs.

Notes:

• Up to 50 tel. numbers can be programmed for each relay.

• Each tel. number can have a limit to the number of calls so that any further calls are ignored.

• This feature is not applicable to phones with withheld numbers.

• Dialling-in relay control can be reported by SMS.

9. Using prepaid SIM cards

Prepaid SIM cards are NOT recommended for use in David, because they increase the risk

of David malfunctioning due to a possible credit balance under-run.

If you still decide to use a prepaid SIM card, you can configure David for periodic balance

interrogation. If the reported credit balance is lower than the set limit, the credit balance

message will be automatically sent to the service phone numbers. To program this feature you

need to know some data specific to the GSM provider (see the SIM card documentation). The

programming instruction is of the following form:

PC, CRD, xxxx, dd, hhh, pp

where:

PC is the access code

CRD is the name of the instruction for credit balance interrogation

xxxx is the command string to ascertain the credit (GSM network specific, e.g. *104#)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron GD-04 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info