Bedienungsanleitung Jablotron JA-80IR (Seite 2 von 2) (Englisch)

554801

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JA-80IR wireless optical barrier 2 /2 MKU52302

A permanently lit LED on the right indicates that the beam has been

interrupted (or wrongly adjusted). The better the beam reception, the

longer the breaks between the LED flashes. When the LED stops

flashing, continue looking for the ideal position indicated by the highest

voltage measured on the voltmeter.

Setting up the electronic part of the barrier

Both units are equipped with setting switches. The switch located on the side

of the units (on the optical part) allows barrier beam modulation frequency

adjustment from 1 to 4. This setting is useful only for a combination of

multiple JA-80IR barriers where a problem with interference might appear.

For more information see the original user.

There is a DIP switch with five switches. The first two positions are used to

set the reaction time to an interruption of the beam. The shorter the time, the

more precise the interruption detection, but also the greater the susceptibility

to false alarms during worsened optical conditions (snow, fog, ...)

Fig. 7 Reaction time setting

It is possible to set a 2-minute sleep time after an alarm (beam

interruption) in order to save batteries. This setting is done by switching

switch no. 3 (receiver unit), or no. 1 (transmitter unit) to the ON position.

Switches 4 and 5 (receiver unit), or better 2 and 3 (transmitter unit) are

set as a default and you should leave them in the OFF position for the

correct functioning of the device.

Operation testing

The LEDs on the barrier have the following indication functions

Receiver Transmitte

Low battery LED Low battery LED

Alarm LED Power LED

Fig 8 LEDs on the units

The signal battery low LEDs flash when the batteries in the unit are low.

Both batteries (SAFT LSH20 lithium batteries) should always be

replaced at the same time.

The alarm LED flashes during beam blocking.

The power LED flashes when the battery in the transmitting unit is OK.

Receive

Transmitter

Fig. 9 Barrier function test

Perform a barrier test in three places (A B and C). The setting is

completed only if the barrier reacts successfully in all three positions.

You should also check the signal transmission to the system control

panel. Only then is it possible to put back the unit covers and secure

them.

Checking the status of and replacing batteries

The detector checks battery status automatically and if the batteries are

running low, it informs the system. The detector remains fully functional.

The batteries should be replaced as soon as possible (within 1 week).

Use SAFT LSH20 batteries exclusively and always replace both at the

same time.

Technical specifications

Power supply 4x LSH20 type lithium batteries (3.6 V 13 Ah)

Average battery lifetime approx. 3 years (with 120 s energy saving mode)

Operating frequency 868 MHz

Radio range – distance from the control panel up to 300 m with direct visibility

Optex barrier parameters

Distance (max.) between the barrier units 60 m

Barrier installation height 0.7 – 1.0 m

Object motion speed as set by user

Battery saving timer 120 s

Enclosure IP55

Max. relative humidity of the environment 95%

Weight 1620 g

Environment according to EN 50131-1 class IV

Operating temperature range -20°C to +60°C

Security grade according to OPTEX

Comply with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-1

Can be operated according to ERC REC 70 03

JABLOTRON ALARMS Inc. hereby declares that the JA-80IR

wireless optical barrier is in compliance with the essential

requirements and other relevant provisions of Directive

1999/5/EC. The original of the conformity assessment can be

found at www.jablotron.com

- Technical Support section

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use.

88,1

217

162,5

83,5

Fig. 10 Unit dimensions

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80IR Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info