Bedienungsanleitung Jablotron JA-80S (Seite 2 von 2) (Englisch)

554811

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The JA-80S wireless fire detector MHS51502 2

Jumper position = FIRE = the control panel responds with a fire

alarm, no matter if the system is armed or not.

Jumper position = INST = the control panel responds with a fire

alarm only if the system is armed. The alarm is not indicated by an

internal LED. This feature is useful if the user wishes to allow smoke

in a room from e.g. smoking or a fireplace, while the control panel is

disarmed when authorized people are present in the building.

Warning

: In the INST position, while the system is disarmed, it is not

protecting against fire. The FIRE / INST jumper only has an effect if the

detector has a natural reaction assigned to its address in the Oasis

control panel. It also has no effect when used with a UC-8x or AC-8x

receiver. Whenever the detector cover is opened, a tamper signal is

sent.

Testing the detector

The functioning of the detector can be tested by pressing and

holding the test button (e.g. for 1 sec). This activates the siren and the

LED flashes (LED only if the fire reaction is set). The strength and

quality of detector signals can be measured by the control panel in

Service mode. During testing by the test button, the detector transmits

signals which can not trigger fire alarms in the control panel.

Warning: Never start a fire in a building to test the detector.

Instead, use smoke-simulating aerosols for realistic testing.

Silencing the siren during an alarm

During a fire alarm, the detector LED flashes (if the fire reaction is set)

and the built-in siren sounds. Under these conditions the siren can be

silenced by pressing the test button, but the LED will continue to flash

until the smoke clears from the room.

Alarm memory in the detector

Normally the detector’s fire-alarm condition lasts until the smoke clears

from the room and the fire-alarm information is stored in the control

panel‘s memory. If desired and the fire reaction is set, a local memory

in the detector can be enabled by pressing and holding the test button

during battery installation. If this function is enabled, after detecting

fire, the detector‘s fire alarm mode continues until the test button is

pressed.

Fault indication

The detector performs regular self-testing. If a fault is detected in the

detector, its LED will start to flash rapidly. In such a case, disconnect

the battery from the detector, and after about 20 secs, re-connect it. If

after a minute the LED still flashes, then send the detector off for

repair.

Battery replacement

The detector monitors its battery voltage and if too low, a transmission is

sent to the control panel to inform the installer or user. The detector

continues to function but with a short LED flash every minute. Battery

replacement should not be delayed by more than two weeks. This should

be done by a qualified technician with the control panel in Service mode.

After battery replacement, test the functioning of the detector using its

test button. Expired batteries should not be thrown into the garbage, but

disposed of according to local regulations.

Removing the detector from the system

If a detector is removed, the control panel announces the removal.

The detector has to be deleted in the control panel before intentional

removal.

Technical parameters

Voltage: Lithium battery type or LST14500 (AA 3.6V)

Typical battery lifetime approx. 3 years

Communication band 868 MHz, Oasis protocol

Smoke detection optical, light dispersion

Smoke sensor sensitivity m = 0.11

0.13 dB/m to EN 54-7

Temperature detection class A2 to EN 54-5

Fire-alarm temperature +60 °C to+ 70 °C

Acoustic power of the built-in siren 80 dB/m A

Operational temperature range -10°C to +80 °C

Dimensions diameter: 126 mm, height: 65 mm

Complies with EN 54-7, EN 54-5 class A2, prEN 54-25, ETSI EN

300220,EN 50130-4, EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

FCC ID: VL6JA80S

Jablotron Ltd. hereby declares that the JA-80S is in compliance with

the essential requirements and other relevant provisions of Directives

1999/5/EC and 1989/106/EC and complies with part 15 of the FCC

rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by

Jablotron could void the user´s authority to operate the equipment.

The original of the conformity assessment can be found at

www.jablotron.com

, Technical Support section

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 483 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-80S Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info