Bedienungsanleitung Jablotron JA-80X (Seite 2 von 4) (Englisch)

555057

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

The JA-80X communicator 2 / 4 MKR51103

3 – Record message No. 3 (Fire)

4 – Record message No. 4 (Tamper)

5 – Record message No. 5 (Panic)

6 – Record message No. 6 (Fault)

7 – Record message No. 7 (Welcome to OASiS) – greeting

8 – Record message No. 8 (Enter your access code)

Pressing the key invokes a timer with beep indication. Five beeps

are to be heard in total with the last beep extended. After this the

recording starts – you record a message by speaking into the

phone’s microphone. The message duration is limited to 9 sec for

message No. 1, and to 3 sec for any of other messages.

After being recorded, the message is immediately re-played. A

message ending is indicated by two beeps. Replaying all

messages (0) can be terminated by pressing *. The recording of

any message can be terminated by pressing # or by hanging up.

Recording the voice message is stopped after hanging up.

Notes:

• You can also remotely record or modify voice messages via a

phone in a call to the control panel. This requires the control

panel to be in Service mode (on the phone keypad, you enter

72x as described above).

• You can change recorded messages anytime using the above

procedure. Messages are stored in a non-volatile memory so

the JA-80X will not forget them when its power supply is

disconnected.

3. ARC reporting

Contact ID (CID) protocol is used for communication with Alarm

Receiving Centres (ARC). If at least one phone number is pre-

programmed for ARC reporting then the communicator tries to

send a report about any event detected by the control panel (as

requested for ARC reporting). Events are reported in the same

order as they are detected. A successfully transferred report

causes a “Report sent to ARC” event report to be stored in control

panel memory.

If transfer to ARC1 is not successful, the communicator starts the

transfer to ARC2 depending on whether a second ARC is pre-

programmed. If the transfer to ARC2 is also not successful, the

communicator tries to transfer the report to ARC1 again and this is

repeated four times. Unsuccessful transmission results in “Report

not sent to ARC” after eight (four) attempts. Then a standard voice

message is sent to the phone numbers according to the event and

settings. After that there are two other attempts (cycles) to deliver

the message to the ARC after 5 minutes and after 10 minutes.

An undelivered report is stored in the memory and is reported

together with the next report – if possible.

Note: Contact ID protocol ensures that all the relevant events are

reported automatically. An idea of the data format is provided in

the table below.

3.1. ARC phone numbers

sequence 75 Mxxx…xx*0

To program tel. numbers of requested ARCs enter:

75Mxx….x*0

where:

M is the ARC memory index: 1=main, 2=back-up

xx..x is the ARC phone number (max.16 digits)

To erase a number from memory M enter: 75M*0

3.2. Installation (alarm system) ID for ARC use

sequence 76 Mx..x*0

The installation’s ID number which is sent to an ARC with every

report can be programmed with:

76x..x*0

where:

xx.x is the installation ID number which identifies your

premises

If a hexadecimal form is needed for the ID specification, use

digits prefixed by “*” for alphabetical characters: *1 = A to *6 = F.

Example: The sequence 7615*1*5*0 will program the hexadecimal

ID 15AE.

3.3. Filtering reported events

sequence 73 nx

Reported events can be filtered according to their type. To

enable/disable reporting events of a particular type (or group of

types) enter:

73nx

where:

n is a group of event types

1 – All events

2 – Alarm triggering events

3 – Alarm cancellations

4 – Setting/Unsetting (Arming/Disarming)

5 – Faults

6 – Maintenance events only

7 – Regular (periodical) reports

x is the Enable/Disable attribute

1 – Report

0 – No report

The factory default setting is 7311.

3.4. ARC report structure

A report to an ARC sent using CID protocol consists of:

installation ID (premises identification), event code, subsystem

number and the number of the source (device or code).

Report code table

Report code

Event

1130 / 3130 Intruder alarm – instant / restored

1134 / 3134 Intruder alarm – delayed / restored

1110 / 3110 Fire alarm / restored

1120 / 3120 Panic alarm / restored

1461 / 3461 Number of incorrect code-entries exceeded alarm /

restored

1140 / 3140 Alarm triggered during control panel power-up / restored

1137 / 3137 Tamper alarm / no tampering

1144 / 3144 Device tamper alarm / no tampering

1406 Alarm cancelled by user

1401 / 3401 Unsetting / setting

3402 Partial setting

3408 Codeless complete setting

1354 / 3354 External communication fault / restored

1300 / 3300 Fault (except device) / all faults restored

1330 / 3330 Device fault / all faults restored

1301 / 3301 Mains dropout longer than 30 minutes / restored

1302 / 3302 Battery fault (except devices) / all battery faults restored

1384 / 3384 Device battery fault / all battery faults restored

1306 / 3306 Switching to Service Mode / Leaving Service mode

1661 / 3661 PGX ON/OFF

1662 / 3662 PGY ON/OFF

1355 Radio communication jamming present

1350 / 3350 Internal communication fault / restored

1602 Communication test

1138 Unconfirmed alarm

1351 Communication fault to ARC1

1393 Annual check request

1551 / 3551 Communicator blocked / restored

List of source numbers

Source number Source

701 Control panel

731 Communicator

741 Wired keypad

001 – 050 Devices 01 – 50

500 Master code

599 Service code

501 – 550 Codes 01 – 50

Subsystem: 01 in all reports

In a split system, for setting and unsetting: 02 = A, 03 = B

For partial setting: 02 = A, 03 = AB

Jablotron JA-80X Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info