Bedienungsanleitung Jablotron JA-80Z (Seite 1 von 1) (Englisch)

554828

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

JA-80Z radio signal repeater 1 / 1 MKG51300_JA-80Z

JA-80Z – radio signal repeater

The JA-80Z signal repeater is a device belonging to Jablotron’s OASiS

system. It has been designed to extend the range of remote devices whose

signal is not strong enough to communicate with the control panel or whose

communication is unreliable. The repeater function lies in the transmission

of a signal received from an enrolled device with a little delay. The delay

ensures that a possible conflict between the repeater transmission and the

transmitting device is avoided. Each device enrolled to the repeater must

concurrently be enrolled to the control panel.

Repeater architecture

• The repeater has 40 addresses for devices and one address for an

OASiS control panel.

• It copies the state of the PGX, PGY, IW and EW outputs of an

OASiS control panel.

• The addresses are filled by sequential enrollment. The enrolled

devices can only be deleted by resetting the repeater.

• Uses an LED and beeper (if connected – just for installing and

testing purposes) to indicate the strength of the signal received from

enrolled devices.

• Compatible with all OASiS detectors and remote controls with the

exception of the JA-84P.

• It does not support transmissions for JA-8xF keypads, JA-80A sirens

and other JA-80Z repeaters.

• Enables a hard-wired detector connection to the INP terminal.

The repeater must be equipped with a backup battery (e.g. SA-

214/1,3) which ensures its operation when there is a power supply

failure

A double-balanced INP input with a fixed natural reaction (delayed loop)

is available for the connection of one hard-wire detector. Activation of this

input is transmitted to the control panel as a signal from a device to which

the repeater has been enrolled in the control panel. The reaction of this

loop can be configured in the control panel.

The repeater front cover is protected with a built-in tamper sensor and the

box must be protected against being torn off the wall with a tamper device

delivered with the package.

Repeater enrollment mode

1. Switch the DIP4 switch to the “ON” position before you connect the

power supply.

2. Open enrollment mode on the control panel and scroll to the required

position for the repeater.

3. While the rechargeable battery is still disconnected, connect the power

input of the repeater, thus sending the enrollment code and enrolling

the device to the control panel. The control panel subsequently enrols

itself to the repeater automatically.

4. You can exit enrollment mode by pressing the „#“ key.

5. It is also possible to enrol other devices to the repeater by the insertion

of batteries.

• Correct enrollment of a device is always signalled by a one-second

flash of the green LED.

• Exceeding the maximum amount of devices (full memory) is

indicated by several quick short flashes of the green LED and the

device in question is not enrolled.

6. You can exit enrolment mode by switching off the DIP4 switch.

Adding devices to the repeater (additional enrollment

mode)

• Switch the DIP4 switch to the “ON” position.

• The devices are enrolled by the insertion of batteries

• Correct enrollment of a device is always signalled by a one-second

flash of the green LED.

• Exceeding the maximum amount of devices (full memory) is

indicated by several quick short flashes of the green LED and the

device in question is not enrolled.

• You can exit the enrollment mode by switching off the DIP4 switch.

Device signal indication

The number of flashes of the green LED on the control panel

motherboard indicates the strength of the signal received from the given

device upon its activation as follows:

1x 25% (1/4) signal strength

2x 50% (2/4) signal strength

3x 75% (3/4) signal strength

4x 100% (4/4) signal strength

If the beeper is connected is the signal strength indicated by one to four

beeps as well.

Rear box tamper sensor installation

The rear tamper sensor (against the box being torn off the wall) works on

the basis of a magnetic contact (supplied with the package). The contact

must be installed during installation of the box.

1. Break off the prepared rectangular opening at the bottom of the box

opposite the circuit board terminal.

2. The remains of the broken-off plastic moulding must be removed using

a sharp tool (knife).

3. Put the box onto the selected surface and mark the fixing holes and the

position of the prepared opening.

4. Attach the permanent contact magnet onto the marked surface.

5. Install and fix the box (the magnet goes through the rectangular box

opening).

6. Stick the magnetic sensor (the second part with the conductors

brought-out) to an interior side of the box (maximum separation from

the magnet should be 2cm).

7. Connect the outputs to the TMP and COM terminals on the

motherboard without a balance resistor.

8. Switch DIP2 to the ON position.

Description of terminals

INP

Double balanced input terminal (two 1kOhm resistors)

TMP

Rear tamper sensor terminal (not balanced)

COM

Common terminal for INP and TMP inputs

Output, copies the state of the EW output of the enrolled

control panel

Output, copies the state of the IW output of the enrolled

control panel

PGX

Output, copies the state of the PGX output of the enrolled

control panel

PGY

Output, copies the state of the PGY output of the enrolled

control panel

GND

Negative pole of the wired detector’s and the temporary

beeper’s power supply

Possitive pole of the temporary beeper (negative is

connected to the GND)

Positive pole of the wired detector’s power supply (protected

by FU1 – F1A)

DIP switch description

DIP1

The input on the INP terminal is switched on (monitored) in

“ON” position

DIP2

The rear tamper sensor is active in the “ON” position

DIP3

No function

DIP4

The enrollment mode is active in the “ON” position

Device reset

Resetting the whole device is irreversible and causes the deletion of the

enrolled control panel and all enrolled devices from the repeater.

1. Switch off the 230V power output and disconnect the backup battery.

2. Connect the RESET jumper and leave it connected.

3. Connect the supply voltage and the battery.

4. Disconnect the RESET jumper.

Technical specifications

Power source 230 V / 50 Hz, max 0.1 A, protection class II

Power supply type A (EN 50131-6)

Backup battery 12 V, 2.2 Ah

Backup power output maximum continuous load 0.7 A

Number of wireless device addresses 40

Hard-wired inputs 1x double balanced input

1x input reserved for the rear tamper contact

EW external warning output switching to GND, max. 0.5A

IW internal warning output switching to GND, max. 0.5A

PGX, PGY outputs max. 0.1 A, switching to GND

Frequency (JA-82R) 868 MHz

Security grade 2

according to EN50131-1, EN 50131-6 and EN 50131-5-3

Environmental class II. indoor-general (-10 to +40°C)

compliant with EN 50131-1

Radio emissions ETSI EN 300220

EMC EN 50130-4, EN 55022

Safety EN 60950-1

Can be operated according to ERC REC 70-03

Jablotron JA-80Z Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-80Z

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info