Bedienungsanleitung Jablotron JA-82Y GSM communicator (Seite 3 von 8) (Englisch)

631258

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

JA-82Y user manual - 3 - MLD51300

Remote control by phone

For a mobile phone, there are two ways to control the system remotely. You can either send SMS

instructions or establish an authorized connection (protected by an access code) to the system. In this

case the system is controlled by a voice menu. Press 9 to switch the phone to alarm keypad

simulation. The phone keypad can be used the same way as the system keypad. Using a fixed line

phone, you can only operate the system by dialling the communicator’s number and establishing an

authorized connection.

The below described way of remote control corresponds to the communicator’s factory default

setting. The configuration can be modified during installation. The installer should clearly explain

any changes to the default setting.

1. General rules for remote control via SMS instructions 

• More than one instruction can be used in a single SMS message. It has to be separated by a comma.

• SMS instructions are not case-sensitive. Only standard English (ASCII) characters are accepted.

• All SMS instruction words (parameters) must be separated by a space. In this document a space in an

SMS instruction will also be denoted by the underline character ‘_’.

• SMS instructions can be sent from a mobile phone or from a GSM gateway.

• If the % character is used, all preceding text will be ignored. The %% symbol ends processing when

used in SMS text – i.e. all the following text will be ignored. It is recommended to use this symbol at

the end of the instruction if the provider sends some additional text after your message

(advertisements etc.).

• Warning: If any extra text is not separated from a valid SMS instruction text by % or %%

symbols, the SMS message will not be recognized and no instruction will be executed.

• Performance of the instruction is confirmed by an SMS reply.

• The default instruction texts can be customized by an installer or administrator. E.g. the command

PGX ON can be changed to SWITCH ON HEATING etc.

2. Setting (arming) by SMS  xxxx_SET

The SET instruction allows you to put the system in to a set (armed) state, fully or partially. If the

system is already set, it will not change its status.

Send an SMS message containing:

xxxx_SET

where: xxxx is a valid access code (user or master)

_ is a space character

Example: Sending 4321 SET will set the system the same way as if the code 4321 had been entered

on the system keypad.

Notes:

• As a factory default, setting (arming) by a SET instruction is confirmed by the system via an SMS

reply.

• When the current system status does not allow system operation (e.g. when in programming mode),

you will be notified about the situation via an SMS reply.

• In a split system, an xxxx_SET instruction will only have an effect on the section to which the code

xxxx belongs.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JA-82Y GSM communicator Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-82Y GSM communicator

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info