555059
8
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
JA-82Y user manual - 8 - MLD51300
Programming in maintenance mode
Programming in maintenance mode requires access to be enabled by a service technician.
Otherwise, no programming is possible – any instruction sequence will be rejected by the
system and the keypad will beep four times.
The following description is intended for a system administrator, who knows the control panel
master code. All the settings can be performed via keying-in on a system keypad. An unfinished
sequence can be cancelled by pressing the # key. A sequence is only stored in control panel memory
(or executed) after the sequence has been completely entered. All the settings are only applicable if
the control panel is in maintenance mode. To enter maintenance mode, first make sure, that the
system is completely unset. Then enter the following sequence on the system keypad:
0 master code (card) The keypad will display Maintenance mode.
In maintenance mode it is possible to set transmission parameters, measure the GSM signal strength,
enable/disable remote access, set the forwarding of incoming messages, record voice messages and so on.
More details with descriptions can be found in the installation manual.
Wrongly set parameters could limit or cancel some of the
functions (alarm reporting, faults,..). When you change any
parameters, test that the system works properly.
Remote access by Internet
The system can be accessed remotely via Olink software version 2.0 and higher, which allows
complete programming by installers and also operating the system by end users. The GPRS service
(or, alternatively, SMS) is used for data transfer.
Remote access is provided by Jablotron Alarms free-of-charge (only the data transfer from the
premises is charged). The installation technician can set up remote access according to the desired
arrangement.
Accessing the communicator remotely requires its SIM card to be enabled for GPRS data
transfer. Only then can the device work properly.
You can operate the system directly using a virtual keypad by entering a programming
sequence, Olink can open a command line where the sequences can be entered the same way as if
they were entered from a system keypad. By pressing the submit button you send the instruction via
the internet network to the communicator where it will be processed. More details with descriptions
can be found in the installation manual.
The list of events can be opened in any control panel state, therefore it is not necessary to put the
control panel into a specific mode (like unsetting or switching to Maintenance Mode). The events
list records the last 255 events.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jablotron JA-82Y wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Jablotron JA-82Y

Jablotron JA-82Y Installationsanweisung - Englisch - 13 seiten

Jablotron JA-82Y Bedienungsanleitung - Holländisch - 14 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info