Bedienungsanleitung Jablotron JA-82Y (Seite 12 von 13) (Englisch)

555059

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

The JA-82Y GSM communicator installers manual 12/12 MDL51108

•

13. Communicator programming sequence overview

Sequences beginning with “8“ are also accessible from Maintenance mode if the change of telephone numbers in Maintenance mode is enabled (OASiS control panel sequence

251)

Function Sequence Possible options Factory default settings

Communicator language setting 991 xx

xx=01 to 18

Language selection affects SMS texts and basic

voice menu features

English

GSM signal strength measuring 888 range 1/4 to 4/4, exit by pressing # -

Tel. number programming for reporting to

telephones

81 M xx..x ∗0

M = memory 1 to 8; 0 is for the own SIM card

number;

xx..x = tel. number (max.20 digits)

keying in *9 inserts +, keying in *7 inserts * ,

81 M *0 erases the number in memory M

- remote control by unanswered calls – see 3.4

all M1 to M8 erased

Selection of events to report by SMS 82 M uu x

M = tel. number memory 1 to 8

uu = event code, see the 3.4

x=1 report, x=0 no report

in a split system, alarm reports are defined for

sections A, B, or ABC

M1 alarms and faults from sections A, B, C by SMS.

M2 and M3 Alarms from sections A, C by SMS and

phone calls

M5 and M6 alarms from sections B, C by SMS and

phone calls

M4 alarms from A, C and M7 alarms from B, C by

SMS

M8 faults only by SMS from A, B, C sections

Selection of events to report by phone call 83 M uu x

See the List of events which can be reported to

your phone and their factory default settings

Codes associated with enrolled telephones 84 M xxxx

If a codeless SMS arrives from telephone number

M, xxxx is used as a code, keying in 84 M *0 erases

the given code

No code

Allowing remote access from telephone

numbers

85 M x

Allow remote access by authorized numbers M1 –

M8,

x=1 allow, x=2 deny

allow

SMS and instruction text editing

The texts can be changed by OLink software or by sending an instructional

SMS: code TXT n,text,n,text...

See 6.8

Voice message recording

The recording is performed via a mobile phone; the system must be in service or user mode. Dial the system SIM card number from

your telephone. When the system answers, key in the SC, MC, UC code and then key in 892. The communicator will announce:

“You are in voice message recording mode, see the installation manual.“ see 6.9

Enable reporting to phones 901 x

x=0 disabled

x=1 enabled (all programmed)

x=2 enabled without reporting setting/unsetting

by users 41 to 50 (codes, cards & key-fobs) and

master code setting/unsetting

enabled

Enabling remote access 802 x

x=0 no

x=1 yes (by phone and Internet)

x=2 yes, but only by enrolled phones

1=yes

Forwarding of incoming SMS messages 801 x

x=0 no, x=1 if the incoming text is not an SMS

instruction it will be forwarded to the first

programmed number in memories M1 to M8

yes

Autoconfiguration of GPRS 903 x

X=0 autoconfiguration disabled

x=1 autoconfiguration enabled

Autoconfiguration enabled

SMS instruction confirmation 904 x x=0 no, x=1 yes (by SMS reply) yes

Reaction to incoming calls 905 x

x=0 no reaction

x=1 answers after 15s ringing

answers after ringing for 15s

GSM signal dropout indication 906 x x=0 no, x=1 yes (15min. dropout =fault) no

Time synchronization via SMS 907 x X=0 off, x=1 synchronization on on

Phone speaker loudness 909 x x=0..9, 0=minimum,9=maximum 5

Number to be called to maintain SIM card

validity

910 xx..x*0

xx..x = tel. number (max.20 digits), 910*0 erase the

number

Erased

Restriction of the number of sent SMS to

max. 50 SMS per 24 hours

803 x 1=restriction enabled, 0=restriction disabled restriction enabled

SIM card credit interrogation

You can inquire about credit balance by sending the SMS instruction: code CREDIT uu..u xx yyy zz where code = master or

service code, uu..u = GSM network command string to ascertain the credit (e.g. ∗104#), xx=auto-interrogation frequency in days,

yyy=minimum acceptable balance, zz= the textual position at which the number showing the balance starts in the reply message

from the GSM provider. If the credit is lower than the set minimum value, the provider’s SMS will be auto-forwarded to numbers M1

and M8 for someone to top up the pre-paid SIM card

Programming by SMS

The system can be programmed remotely via SMS instruction code PRG seq, seq,... where seq are programming sequences set

in the same way as from the keypad (e.g. 8080 PRG*08080 201 # sets the 10s exit delay

(a space in the sequence causes a 500ms pause)

Registration code

911 xx...x ∗0

xx..x = tel. number to which the registration code

should be sent

Re-registration to the GSM network 893

the communicator disconnects from the GSM network and then re-registers itself, this function can also b

performed by SMS: code GSM

Communicator reset 998080 Resets to the factory default settings and erases all phone numbers, text will not be changed

SIM card’s PIN code

920 xx..x ∗0

xx..x = PIN, 920*0 erases the PIN (to use a SIM

card with a disabled PIN)

erased

GPRS parameter settings

by SMS instruction: code GPRS apn user pass where apn = APN, user = username, pass = password (only enter the APN if the

name and password are not required by the GSM provider)

Tab. 7 communicator programming sequence

Jablotron JA-82Y Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron JA-82Y

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info