Bedienungsanleitung Jablotron JA-88P (Seite 2 von 2) (Englisch)

554798

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

JA-88P outdoor wireless motion detector 2 / 2 MKU52103

Setting up the optical part of the PIR detector

The optical part of the detector contains two PIR sensors with non-

overlapping 94 lobe detection and high false alarm and pet detection

immunity.

Installation at 3.0 m

above the floor

12 m

16 m

When installing the detector 2.5m

above the floor, use the joint holder

and swivel the detector by 2.5°(one

click) upwards to achieve a 12m

detection distance.

The above-mentioned detection characteristics apply if the detector is

installed vertically in the guarded area. If a shorter detection range is

required, do not tilt the detector on the joint. Use the supplied self-adhesive

mask foils:

9 m

USE

MASK

4 m

1+2+3

USE

MASKS

5,5 m

1+2

USE

MASKS

Masking using strips of the supplied foil can also be used to avoid

unwanted moving objects (e.g. a tree). Use the supplied protective hood for

protection against sun and rain.

The joint can be used to adjust the detector position along two axes. When

installing the detector at the height of 2.5m, swivel it by 2.5° (one click)

upwards to achieve a 12m detection range.

Setting up the electronic part of the PIR detector

It is possible to set three levels of detector sensitivity using the switch on

the left of the bottom PIR – the levels are marked with letters:

L low – low sensitivity for places with false alarm risks

M middle – medium sensitivity

H high – high detection sensitivity

Other detector parameters can be set with a switch:

normal operation area coverage test

energy saving mode 120 s 5 s

standard detection increased detection immunity

Keep set as shown here

LED indication disabled LED indication enabled

Area coverage test (DIP1) – the energy saving mode is not applied and

each detectable movement is indicated by an LED. The alarm is always

transmitted regardless of the energy saving mode settings (DIP2). The

energy saving mode (DIP2) is similar to that of the JA-80P detector. When

the detector is activated and transmits the information to the control panel, it

stops detecting motion for a set time. The activation of the LED (DIP6)

serves as an indication of the detector function – i.e. the area coverage. The

detector always transmits information to the control panel – disable the LED

to save the batteries in ordinary operation.

Operation testing

When the batteries are connected, the detector needs approx. 90 seconds

for stabilization. The LED keeps flashing all the time. Use the switch to

commence the area coverage test. Test the correct coverage of the guarded

area and whether the detector detects motion outside the guarded area.

Each movement is indicated by a flashing detector LED and the information

is concurrently sent to the control panel.

When you have tested the correct functioning of the detector, stop the area

coverage test, check whether the indication LED is off and set the energy

saving mode to 120s. This is necessary to meet the declared battery lifetime.

Normal detector operation

Each time the sensor is activated, the information is transmitted by a radio

signal. When the detector cover is opened or the detector is removed from

the bearing plate, a tamper signal is transmitted. The detector also regularly

(every 9 minutes) transmits control signals which serve the control panel to

check the presence and readiness of all devices in the installed system.

The masking protection function

The detector has an anti-masking function – i.e. protection against

masking of the detector’s field of sight. If an object is detected in front of

the detector for more than three minutes, the detector sends a tamper

signal.

Three short flashes of the LED indicate masking (the LED must be

enabled). When the object has been removed, the indication (tamper

signal) ceases after one minute.

It is possible to set three levels of this function using the switch on the right

of the bottom PIR – the levels are marked with letters:

HI high – high masking detection sensitivity

STD standard – standard masking detection sensitivity

OFF off – function disabled (default setting)

This function is disabled as a default.

Checking the status of and replacing batteries.

The detector checks battery status automatically and if the batteries are

running low, it informs the system that they need replacing. The detector

remains fully functional. The batteries should be changed as soon as

possible (within 1 week). Use 3.6 V AA batteries exclusively and always

replace all three at the same time. When the cover has been closed, the

detector switches to normal operating status.

Technical specifications

Power supply 3x type LS(T)14500 (AA 3.6 V 2 Ah) lithium batteries

Average battery lifetime approx. 3 years (with 120 s energy saving mode)

Operating frequency 868 MHz

Range – distance from the control panel up to 300 m with direct visibility

Optex detector parameters

Detection characteristics 12 m / 85° ; 94 segments

Recommended installation height 2.5 – 3.0 m

Object motion speed 0.3 – 1.5 ms

-1

Battery saving timer adjustable 5 s or 120 s

Detector cover conformance IP55

Max. relative humidity of the environment 95%

Operating temperature range -20°C to +60°C

Environment class according to EN 50131-1 IV

Security grade according to OPTEX

Weight 620 g

Comply with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-1

Can be operated according to ERC REC 70-03

266

205

148

JABLOTRON ALARMS a.s. hereby declares that the

JA-88P is in compliance with the essential

requirements and other relevant provisions of Directive

1999/5/EC.

The original of the conformity assessment can be found

at www.jablotron.com - Technical Support section

Note: Although this product does not contain any

harmful materials we suggest you return the

product to the dealer or directly to the producer

after use.

123456

Jablotron JA-88P Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info