Bedienungsanleitung Jablotron JA-89P (Seite 2 von 2) (Englisch)

554818

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The JA-89P wireless motion detector 2/2 MKU51102

Internet: www.jablotron.com

Tel.: 483 559 911

fax: 483 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

You can restrict the detection angle by adhesive masking strips supplied

with the package. This way you can eliminate problematic parts of the

detection area. The strips are to be stuck on the relevant lens segment from

the inner side.

The PIR detection sensitivity can be configured by a 3-pole switch located

under the upper sensor. The letters correspond to sensitivity levels as follows:

L low – applicable to bad conditions

M middle

H high

Other parameters can be configured using a DIP switch:

LED indicator OFF LED indicator ON

120 s 5 s battery saving timer

4x 2x pulse count

The LED indicator is to be used for PIR detector testing. For normal detector

operation the indicator should be turned off in order to save the battery.

The JA-89P is capable of automatically switching to battery-save mode.

Triggering a PIR sensor is signalled to the control panel after which the

detector switches to sleep mode for a configurable time. During this time the

detector ignores any further movement.

A filter for detector signalling can be established by setting a trigger counter.

Either 2 or 4 triggering events (which have to be detected by both PIR

sensors due to the AND logic) can be configured to cause signals to be sent

to the control panel.

Testing operation

Turn the LED indicator on, set the battery-save timer to 5 seconds and close

the detector. Every 5 seconds any movement in the detection area will be

indicated by the LED indicator and the alarm information will be sent to the

control panel. You should test both the sensitivity to movements in the

detection area as well as the detector’s insensitivity to any movement outside

the area of protection. Take into consideration that the detection range may

vary according to local conditions.

After finishing the test, it is recommended to turn off the LED indicator and

set the battery-save mode duration to 120s.

Operation

The detector uses radio signalling for all types of detected events:

movement detection, cover opening, tearing the detector off its position, and

communication checking. The communication checking is automatically

performed at 9 minute intervals for the system to test that all its devices are

present and ready for operation.

Battery replacement

The detector monitors its battery voltage and if too low, a report is sent to

the control panel to inform the installer or user. The detector continues to

function. Battery replacement should not be delayed by more than one week.

Before battery replacement, you need to ensure that the receiver (control

panel) is put into a state which permits opening the detector cover. Only use a

lithium battery of type AA 3.6 V. After closing the cover, the detector starts to

operate in its normal mode.

Note:

The detector’s LED flashes if you accidentally insert a low battery.

The detector will not work after an expired battery has been inserted.

Trouble-shooting

Problem Probable cause Remedy

Lower detection area is

unnecessarily long.

Set the detection area

properly.

The detector is exposed to

direct/reflected light (sun

light, car lights etc.).

Remove the reflector,

mask the area exposed to

the reflection of light or

change the detector

position.

The detector

makes false

intrusion

alarms.

There is a moving object in

the area (laundry on the

clothes-line, plants etc.)

Remove the moving object

or change the detector

position.

The detection area is too

close to the detector.

Set the detection area

properly.

Sensitivity is set to low (L). Change sensitivity to

medium (M) or high (H).

Occasionally

The detector is in battery-

save mode.

While testing operation,

set the battery-save timer

to 5 seconds.

Low battery. Replace the battery.

LED does not light. Turn the LED switch ON.

Detector

ignores any

movements.

LED indicator lights but

there is no reaction in the

control panel.

The control panel is out of

range, check the battery,

try to reposition detector or

control panel.

198

108

Dimensions

Technical specifications

Voltage: Lithium battery type LS(T)14500 (3,6V AA)

Typical battery lifetime approx. 3 years (120 sec sleep mode)

Communication band 868 MHz

Communication range approx. 300 m (open area)

Specification of the Optex VX 402R detector

Coverage 10 m / 90°; 14 segments

Installation height 0.8 – 1.2 m

Detected speeds 0.3 – 1.5 ms

-1

Battery saving timer either 5 or 120 seconds

LED indicator only in test mode

Operational environment class IV, according to EN 50131-1

Security grade 2, according to EN 50131-1

Operational temperature range -20°C to +50°C

Enclosure IP54

Maximum relative humidity 95%

Dimensions 198 x 80 x 108 mm

Can be operated according to ERC REC 70-03

Security grade 2, according to EN 50131-1, CLCITS 50131-2-2, EN 50131-5-3

Jablotron Ltd. hereby declares that the JA-89P is in compliance

with the essential requirements and other relevant provisions of

Directive 1999/5/ES. The original of the conformity assessment

can be found on the web site www.jablotron.com

, Technical

Support section.

Note: Dispose of batteries safely depending on battery type and

local regulations. Although this product does not contain any

harmful materials we suggest you return the product to the dealer

or directly to the manufacturer after use.

123

Jablotron JA-89P Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info