Bedienungsanleitung Jablotron JK-06 (Seite 2 von 4) (Englisch)

554867

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

JK-06 PROFI TEL KIT 2/4 MGK55107

4. Detectors and accessories installation

a) Install the JA-60N magnetic detector to the door (antenna

pointing up or down)

b) Install the JA-60P motion PIR detector

attach

open

click

rear tamper

lever

Don't tight

this screw

2,5

1,5

0,5

1,6 3,7

range

[m]

height

[m]

120

zone A

zone B

zone C

zone A

zone B

zone C

JA-60P coverage

avoid location against windows or close to a heater

c) Select Instant or Delay reactions via DIP switches inside

the detectors.

d) Connect detector’s batteries (pull out the red tape to

activate the batteries)

e) Attach the keypad to the desired location

f) Plug in the UC-260 wireless siren into a power socket

5. Enrollment of additional accessories

If you install additional detectors (max. 32), you have to enroll

them. The system should be in the P mode (if not enter F0 6060):

a) Press 1 to open the learning mode*

b) The next free detector position will be displayed on the

keypad.

c) Install batteries into all new detectors step by step to enroll

them (system will automatically offer the next free position)

d) To scroll through sensor positions, press 1 (up) or 7 (down)

e) To enroll a second detector to an occupied position press 5

before you install the detector’s batteries

f) To exit the learning mode press the N key

Wireless keypad (JA-60F) enrolls after you install its battery

while in the learning mode.

Remote control (RC-4x) enrolls after you press and hold both

and buttons while in the learning mode.

Wireless outdoor siren (JA-60A) enrolls after it is powered

while in the learning mode

To enroll the control panel to UC receivers enter 299 on the

keypad while in the P mode

Check individual item manuals for more details

*Learning mode will also open after shortening of the Reset pins

in the control panel.

6. Detectors and controllers testing

a) The system should be in the P mode (if not enter F0 6060)

b) Trigger detectors – their addresses (1=door and 2=PIR) should

be indicated (if the PIR detector does not react, reenter its

testing mode by opening and closing its cover)

c) Press button

on the RC-4x remote control – c2 will be

indicated

7. To measure strength of the radio signal

a) While in P mode, press 1 and then using 7 scroll to position 1

b) Press 8 to start measuring

c) Activate the door detector to view its signal strength

d) Using the 1 key, scroll to the next position (2 PIR) and

check its signal strength (if the PIR detector does not react,

reenter its testing mode by opening and closing its cover)

e) Repeat step d) to check all enrolled items. The wireless keypad

(c1) signal is indicated after you trigger its tamper. Remote

control (c2) is indicated after you press it’s button

f) Change the location of an item if its signal is lower than 2

g) Return to P mode by pressing the N key

8. Programming of the system

a) System should be in the P mode (if not enter F0 6060)

b) Using the following sequences you can program:

Function Sequence

comments

Your installer

code*

5 xxxx xxxx

6060 factory default

xxxx new code

Exit delay

20x

3=30sec factory def.

Entrance delay

21x

3=30 sec factory def.

Alarm duration

22x

4=4min factory def.

Telephone numbers

entering

7 yy…y F n

yy…y=tel. number

n=memory 1 to 4

7F0Fn will erase memory

Alarm voice

message recording

then push and hold REC button on the

telephone module and talk to the

microphone – max. 10sec.

Time & date

4 hh mm DD MM YY

Remote Comlink

access code*

07xxxxxxxx

00000000 factory def.

xx..x=new code,8digits

Remote Comlink

access enabling

05x

x=0 disabled

x=6 enabled after 6 rings

See control panel installation manual for more details.

* Must be changed

9. Finishing installation

a) Fill in information on the sticker label and attach it inside the

keypad cover.

b) Switch the system to standby (by pressing the N key)

c) Instruct the user how to operate the system

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JK-06 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info