Bedienungsanleitung Jablotron JK-84 Oasis (Seite 2 von 2) (Englisch)

554794

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The JK-84 “Oasis” wireless alarm kit 2 / 2 MKE59901

tab

4. Enrolling more wireless devices

The system can be extended with more wireless devices (a maximum

of 50 can be enrolled). To enroll another device, the CP should be in

service mode, if it is not enter ∗ 0 8080 (while the system is unset).

1. On the keypad, key in 1 to enter enrollment mode.

2. The next vacant address is displayed (scroll to other addresses

using the arrow keys if desired).

3. Connect up the device’s battery to enroll the device to the CP.

Successful enrollment is confirmed by the A indicator lighting. The

next vacant address is then displayed.

o The RC-86 key-fob can also be enrolled by pressing and holding

a pair of its buttons

+ (or + ).

4. Exit enrollment mode by pressing the # key.

• To enroll the CP to UC-82 or AC-82 modules, enter 299 while the

CP is in service mode with the receiving module in enrollment mode.

5. Testing device functionality

1. The CP should be in Service mode, if not enter ∗ 0 8080

2. First trigger the device under test (e.g. a detector). The keypad

(with its flip cover open) then indicates triggering of the device if

the device is functioning correctly and is enrolled.

• Motion detectors are best tested within 15 minutes of closing their

covers as after that they only react to frequent movements once

every 5 minutes (to restart a device’s test mode, open and close the

detector housing again).

6. Checking a device’s radio signals

1. The CP must have its antenna connected and should be in Service

mode, if not enter ∗ 0 8080

2. Enter 298, the lowest address with enrolled device will be displayed.

3. Trigger the device linked to this address – the keypad (with its

flip cover open) then shows the device’s signal strength in the

range ¼ to 4/4 (it should be at least 2/4, if not, relocate the device)

o Motion detectors are best tested within 15 minutes of closing their

covers as after that they only react to frequent movements once

every 5 minutes (to restart a device’s test mode, open and close

the detector housing again).

o To test the JA-80F keypad signal, trigger the connected magnetic

door sensor or activate the keypad’s tamper sensor.

o To test the JA-80L siren signal, press the siren’s button.

4. To select the next enrolled device address use the arrow keys.

5. To exit signal measurement mode, press the # key.

7. Programming the system

1. The CP should be in Service mode, if not enter ∗ 0 8080

2. Enter the appropriate programming sequences to select the desired

functions (a complete list of them is in the CP and communicator

manuals).

Function Sequence Note

New service code

5 xxxx

xxxx

Factory default: 8080

xxxx = new code

Exit delay 20x

x = multiples of 10 sec.

(e.g. 205 = 50 sec)

Factory default: 30 sec

Entrance delay 21x

x = multiples of 5 sec.

(e.g. 204 = 20 sec)

Factory default: 20sec

Alarm duration 22x

x = 1 to 8 means 1 to 8 minutes

and 9 means 15min.

Factory default: 4 min

Time and date entry 4 hh mm DD MM YY

8. Editing keypad text strings

1. The CP should be in Service mode, if not enter ∗ 0 8080

2. Press and hold the ? key to enter editing mode.

3. Keys: 1 & 7 scroll through characters and numbers,

4 & 5 move the cursor,

2 erases the highlighted character,

& are for the selection of text strings,

# exits editing mode.

Editing text only affects the text in that particular keypad. A more

convenient way of text editing is with a PC running Olink software.

9. Finishing off the installation

1. Exit service mode via the # key and demonstrate clearly how to

operate the system to the user(s).

2. Recommend the user to change the default master 1234 code to a

new master code.

Entry Function

code / card Setting/unsetting (arming and disarming)

ABC Complete arming (all sections)

A Partially setting A (if used)

B Partially setting AB (if used)

∗4

Reading the event memory (4 scrolls backwards)

∗5

Changing the MASTER code/card (e.g. *5 1234

2789 2789)

∗6

To create a new user code/card (e.g. *6 1234 03

3344 programs user code number 3, to erase the

code enter: *6 1234 03 0000)

∗7 code/card

To secretly signal operation (unsetting) under duress

∗8 a ∗9

PGX and PGY control (if used)

∗0 MASTER

code

Maintenance mode (testing, overview of codes,

bypassing,…)

Exiting maintenance mode or terminating an

incomplete entry

Displays status details (triggered detectors, fault

causes or the status of PG outputs …..)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron JK-84 Oasis Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info