Bedienungsanleitung Jablotron KB-350M (Seite 1 von 2) (Englisch)

555003

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Klávesnice KB-350 Antivandal 4 / 4 MEV51303 Klávesnice KB-350 Antivandal 1 / 4 MEV51303

Reset

If the master code or service code is forgotten or if you connect a new keypad, it is necessary to reset the

control unit. Disconnect power and connect the RESET jumper and after 20sec. reconnect power. After 5

seconds, disconnect the jumper. This procedure will restore the factory default settings (master code = 1234,

service code = 9999, all user codes are erased) and it will also enroll connected keypads to the control unit.

output control

PANIC mode

factory setting:

MC 1234

UC1-UC9 deleted

Code setting

setting deleting

save and exit

MC master code

UC1-UC9 user codes

operating

mode

Parameters setting

Output N.1 mode

Output N.2 mode

Panic mode

Number of attempts

Tamper output reaction

New Service Code

values

default

00- latch

xx- pulse (01-99 sec)

0=off, 1=on

1-9 or 0=unlimited

must be entered 2x

Note: Although this product does not contain any harmful materials we suggest you to return the product to

the dealer or directly to the producer after usage.

KB-350M Digital Access Keypad

The KB-350M access control keypad can operate electric devices such as door locks, gates, or security

systems. It consists of two parts - a keypad and a control unit. Both parts are connected by a two-core

cable. One or two keypads can be wired to each control unit (e.g. they can be installed on both sides of a

single door). While one keypad is being accessed, the second keypad is temporarily bypassed.

A separated control unit insures maximum security. The communication in the cable from the keypad to

the control unit is encrypted with a sophisticated floating code protocol. This ensures that there is no other

way to operate the device than by entering a valid access code.

The keypad itself is made of a solid alloy and it is suitable for vandal proof applications.

Specifications

Power 10 – 16 V AC or DC, 60mA no relay on, 120 mA both relays on

Keypad connecting cable 2 core cable, max. 100 m, arbitrary polarity

Output relay (output 1) over-switching contact 1 A / 60 V

Transistor output (output 2) switches to GND – max. current 1.5 A / 25 V

Tamper output max. 100 mA / 25 V (control unit, keypad and cable tamper protection)

Power output rectified voltage from PWR input terminals - max. 1.2 A for max. 5 sec

Access codes 4, 5 or 6 digits, 1 master + 9 user codes (each code can be addressed to output 1

or 2)

Output modes programmable duration of pulse (from 1 to 99 sec.) or latch mode

Number of attempts programmable

Security grade 3 midle to high risk (EN 50131-1)

Keypad working environment outdoor use (class III), -25 °C to 50 °C (EN 50131-1)

Enclosure IP52 (EN 60529), mech. resistance IK08 (EN 50102)

Control unit working envir. indoor – general (class II), -10 °C to +40 °C (EN 50131-1)

Complies with the essential requirements of: 89/336/EC EMC Directive - Protection concerning electromagnetic

compatibility when is used for its intended purpose. Original of the conformity assessment can be found

at the web page www.jablotron.cz, section Technical support.

Installation

Keypad can be installed on a standard electro installation box (screw spacing - 60 mm).

• remove front panel - use the provided tool to unscrew the 4 screws

• connect the keypad’s terminals with the control unit’s BUS terminals using two wires (twisted pair) (e.g.

SYKFY cable), max. distance – 100 m, arbitrary polarity

• up to 2 keypads can be wired in parallel, the total length of all cables should not exceed 100 m

• reattach the keypad after powering and testing (see bellow)

Note, if you change or add a keypad, you must reset the control unit!

Control unit can be installed directly on a wall or on an installation box. Terminal descriptions follow:

C, NC, NO over-switching relay contact (output N.1), max. 1 A / 60 V, (C=common, NC=normally closed,

NO=normally opened)

TMP, TMP NC tamper output, max. 0.1 A / 25 V; opens when a control unit is opened, if any keypad is

lost, if the connecting cable is cut or shortened or if a pre-programmed number of attempts to

enter the correct code is exceeded or if a panic sequence is entered (programmable)

OUT transistor output (output N.2), max. 1.5 A / 25 V. It switches to GND when activated.

+E rectified power voltage (from PWR input terminals). It can be used for the powering of an

electric door lock etc. Maximum permanent load is 0.25 A, short period load (max. 5 sec.) -

can be 1.2 A (for electric strike release). Note that a corresponding power supply must be

used to power the unit (RWR terminals).

GND ground terminal of internal power supply

BUS, BUS bus line terminals for keypad connection. Up to 2 keypads can be connected in parallel. Twist

pair (e.g. SYKFY) is recommended, max. length – 100 m. Polarity is arbitrary. The bus is used

for both powering the keypads and for data transfer (a highly secure floating code is used).

Note, if you change keypads, you must reset the control unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron KB-350M Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info