Bedienungsanleitung Jablotron KB-350PK (Seite 2 von 2) (Englisch)

555004

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Digital Access Keypad KB-350PK 2 / 4 MEV51601 Digital Access Keypad KB-350PK 3 / 4 MEV51601

PWR, PWR power supply input (10 - 16 V AC or DC). Adapter

DE20-15 or backup power supply BP-12 is

recommended.

LED indicators on the control unit:

green output relay is triggered (output N.1)

red output transistor is triggered (output N.2)

yellow tamper is triggered (TMP)

LED indicators on the keypad:

green output relay is triggered (output N.1)

red output transistor is triggered (output N.2)

yellow both output N.1 and N.2 are triggered

green flashing programming mode

red flashing keypad is bypassed (the other one is being

used or a number of attempts to enter the

code was exceeded)

First powering

Connect the RESET jumper in the control unit and switch on the power supply. After 5 seconds, disconnect

the jumper. This procedure will enroll all of the keypads into the control unit. Test the keypads by entering the

factory default code 1234. If everything is operating correctly, the green LED on the keypad should switch on.

Leave the RESET jumper disconnected.

Access codes setting

10 different access codes can be used. One code is a master code which can operate the keypad as well

as set the other user codes. The factory default master code is 1234; the other user codes are blank. All

access codes can have 4,5 or 6 digits and a corresponding output (N.1 or N.2) can be assigned to each

code.

Enter: ∗ 5 master code (default 1234) first. The green LED will start flashing (programming mode).

• Master code setting:

0 xx...x ∗ xx...x ∗ y

where xx...x is a new code (4 to 6 digits), after pressing ∗ it is necessary to reenter the new code

y enter 1 or 2 to assign a corresponding output

• User codes setting:

A xx...x ∗ y

where A is a user code number (from 1 to 9)

xx...x is a new user code (4, 5 or 6 digits)

y enter 1 or 2 to assign a corresponding output

• User code deleting:

A ∗ where A is a code number (1 to 9)

To exit the code setting mode press the ∗ key. If you press the # key, none of the codes entered in the

current session will be stored in the memory.

Optional parameters setting

Enter: ∗ 6 service code (default 9999) in order to enter the parameters programming mode. The green

LED will start flashing.

• Working mode of output N.1 (relay):

1 xx

where xx is a period of time during which the relay is switched on (01 – 99 sec.). If 00 is entered, then the

output N.1 will be set to a latch mode (it changes its status whenever a valid assigned code is entered)

• Operating mode of output N.2 (transistor):

2 xx

where xx is a period of time during which the relay is switched on (01 – 99 sec.). If 00 is selected, then the

output N.2 will be set to a latch mode (it changes its status whenever a valid assigned code is entered)

• Panic (access under duress ∗ 7 is pressed before a valid code):

3 x

where x can be 0 = off, 1 = on (if ∗ 7 is pressed before a valid code, the TMP output is triggered for 3

seconds simultaneously with the associated output reaction)

• Number of attempts to enter an access code:

4 x

where x is the maximum number of attempts (0 = no check). If this number is exceeded, the keypad is

blocked for two minutes (can be overridden with a repeated entry of a valid code). The TMP output can

also be triggered (see following setting).

• TMP output reaction if a number of attempts to enter a code has been exceeded:

5 x

where x can be 0 = no reaction, 1 = triggered for 3 sec.

• New service code setting:

6 xx...x ∗ xx...x ∗

where xx...x is a new service code (4, 5 or 6 digits), code must be repeated after pressing ∗

To exit the programming mode press the ∗ key. If you press the # key, programming will not be stored.

Example two doors access control. AC or DC power supply may be used. Pulse length on outputs N.1 and

N.2 should be set to 1 – 5 sec. (depending on the type of electric lock). Garage gates, parking bars etc.

can be controlled in a similar way.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron KB-350PK Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info