Bedienungsanleitung Jablotron RC-60 (Seite 2 von 2) (Englisch)

554889

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

RC-60 Remote Control

The RC-60 is a wireless transmitter designed to control Jablotron

control panels via 3rd party wired access control devices (e.g.

proximity cad readers, mechanical locks with switches etc.). The RC-60

converts control signals from these devices into the wireless control

signals accepted by the JA-60, JA-63 and JA-65 control panels.

Additionally, it can be used to trigger UC-2xx receivers for various

home automation applications.

There are two input terminals (A & B) as well as a tamper input. The

tamper signal is transmitted if the RC-60 is opened or removed from the

wall.

The battery status of the RC-60 is checked automatically.

RC-60 Remote Control 2 / 2 MGW51006

Specification

Power supply 2 AAA alkaline batteries

Battery lifetime approx. 1 year

Frequency 433.92 MHz

RF Power

10 mW

Coding digital floating code

Operating range up to 100 m (open area)

Inputs A and B triggered by switching to GND

TMP tamper input must be connected to GND

Input wires length max 0.5 m

Environment class II, general interior (-10 to +40 °C)

Can be operated according to ERC REC 70-03

Complies with ETSI EN 300 220, ETS 300 683, EN 60950

Hereby, Jablotron Ltd., declares that this RC-60 is in compliance

with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

Original of the conformity assessment can be found at the web page

www.jablotron.cz, section Technical support.

Installation

• Open the cover by pressing in the tab on the bottom side of the detector.

• Electronics and batteries are located inside the front cover.

• Attach the bottom part to the wall or the frame of the door or window

using the provided screws.

• Be sure that the antenna is vertical (pointing up or down).

Triggering

inputs

Tamper

input

Example of connection

Terminals

There are 4 input terminals:

TMP – when disconnected from the GND terminal it triggers the tamper

signal transmission (similar to opening the cover). If you do not use this

terminal, keep it connected to the GND.

A – when connected to the GND, the input A is triggered. If the MODE

jumper is closed, the ARM instruction will be transmitted.

B – when connected to the GND, the input B is triggered. If the MODE

jumper is closed, the DISARM instruction will be transmitted.

GND – ground terminal

Note:

• The triggering wires should not be longer then 0.5 m. It is

recommended to use twisted pairs or screened cables.

• Both mechanical and electronic switches can be used to trigger the A

& B inputs.

Enrolling the remote control

Read carefully the installation manual of the receiver. The JA-60, JA-63

and JA-65 control panels must be set to the enrolling mode. The detector

will generate an enrollment signal after the batteries are installed.

The procedure for enrolling into a UC-2xx is usually the same or an input

must be triggered (see a corresponding manual).

Operating

The MODE jumper enables the setting of the following modes:

MODE jumper is closed – the basic mode:

 Temporary or permanent connection of the A input to the GND

causes ARM signal transmission. Disconnecting from the GND has

no effect.

 Temporary or permanent connection of the B input to the GND

causes DISARM signal transmission. Disconnecting from the GND

has no effect.

This mode is suitable for arming and disarming control panels or for

UC-2xx triggering.

MODE jumper is open - the status and pulse mode:

 Connecting the A input to the GND triggers the ARM signal.

Disconnecting it from the GND triggers the DISARM signal. This

means that the A terminal converts its status into controlling signals.

 Temporary or permanent connection of the B input to the GND

causes PANIC signal transmission. Disconnecting from the GND

has no effect.

Note:

• All triggering signals must be longer then 100 ms.

• The MODE jumper status changes are in effect only after closing the

cover.

Battery replacement

The RC-60 automatically checks the condition of its batteries. If it is

necessary to replace the batteries, the RC-60 will inform the system. If a low

battery is indicated, it should be replaced as soon as possible.

Before the batteries are replaced, the receiver (control panel) must be put

into the mode, which allows for the opening of the remote control. Use only

high quality alkaline AAA batteries for replacement.

Note: Dispose of batteries safely depending on the type of the batteries

and local regulation. Even though this product does not contain any

harmful materials we suggest you to return the product to the dealer or

directly to the producer after usage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron RC-60 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info