The RC-88 is a component of Jablotron’s Oasis 80 alarm system. It is
designed to be a remote control for setting/unsetting
(arming/disarming) an alarm system, triggering panic alarms or
remotely controlling other appliances. The battery-powered wireless
button communicates via OASIS radio protocol.
Installation
If it is to be used as a panic button, then it must be installed together
with the bottom part of its housing and the tamper contacts must be
switched on. Do not install the button on a metal surface (it adversely
affects the range of its transmitter).
• Remove the top part of the housing (using a screwdriver from the
right/left side).
• Release the bottom part of the housing by pressing the 4 tabs in the
corners.
• Install the bottom part to the desired place.
• Reunite the housing containing the electronics with the installed
part of the housing (the tamper spring should press against the wall
where the unit is to be installed, via the hole in the bottom housing).
• Configure the functionality using the DIP switches (see the below
section called ‘Setting the DIP switches’).
• Enroll the RC-88 button to its receiver or control panel according to
the relevant manual.
• Reunite the top housing with the rest of the housing to complete
installation.
LITHIUM
3,6V 1/2 AA
+
A
B
12
ON
TOP
TOP
Setting the DIP switches
Set DIP switches #1 and #2 before finally closing the RC-88 unit as
below:
# OFF ON
1 Tamper contacts and radio
communication supervision
switched OFF
Tamper contacts and radio
communication supervision
switched ON
2 Remote control function -
button A (push the button’s
top)= set, B (push the
button’s bottom) = unset
Panic button function (button A
or B sends a panic signal, i.e.
any pushing)
Using the button with an Oasis JA-80K panel
When used with a control panel, the tamper contacts should be
switched on (DIP switch # 1 in the ON position).
1. Enter enrollment mode on the control panel by keying in “1” in
Service mode (the desired device address can be chosen by the
arrow keys).
2. Install a battery into the RC-88 to activate enrollment.
3. Exit enrollment mode by pressing “#”.
If DIP switch # 2 is OFF, the Natural reaction of the control panel is
remote control - button A = set and button B = unset. If any other
reaction is set in the control panel, it will only be valid for button A.
If DIP switch # 2 is ON, then the natural reaction of the control panel
is a panic alarm – triggered by pressing button A or B.
Testing the RC-88 using a control panel
In service mode, an Oasis control panel can check the radio signal
strength of an enrolled RC-88 button (see control panel manual).
Using the RC-88 as a doorbell button
If the RC-88 is to be used with a JA-80L indoor siren as a door bell
button, set DIP switches #1 and #2 to the OFF position. Enrollment is
described in the JA-80L manual.
Using the RC-88 to control electrical appliances
The RC-88 button can also be used with other Jablotron products
which communicate via Oasis radio protocol, e.g. relay receiving
modules series UC-8x and AC-8x (see the manuals of these particular
products for details). For these applications we recommend switching
DIP switches #1 and #2 OFF.
Note: The RC-88 can be enrolled to several receivers at once.
Battery replacement
If the button is used with an Oasis control panel, then the control
panel monitors the voltage of the RC-88’s battery and if too low, the
control panel informs the installer or user. The button continues to
function but battery replacement should not be delayed by more than
two weeks. This should be done by a qualified technician with the
control panel in Service mode.
Expired batteries should not be thrown into the garbage, but disposed
of according to local regulations.
Always test the proper functioning of the RC-88 after battery
replacement.
Technical specifications
Voltage: Lithium battery type LS14250 SAFT (3.6V ½ AA)
Typical battery lifetime: approximately 3 years (20 daily activations)
Communication band: 868 MHz, Oasis protocol
Communication range approx. 300 metres (open area)
Dimensions 80 x 80 x 29 mm
Operational environment according to EN 50131-1
class II. Indoor general
Operational temperature range -10 to + 40 °C
Complies with EN 50131-1, EN 50131-5-3 grade 2
Can be operated according to EKC REC 70-03
FCC ID VL6RC88
Jablotron Ltd. hereby declares that the RC-88 is in
compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC and complies with
part 15 of the FCC rules. Operation is subject to the following
two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference
received, including interference that may cause undesired
operation.
CAUTION: Changes or modifications not expressly approved
by Jablotron could void the user´s authority to operate the
equipment.
The original of the conformity assessment can be found on
the web site www.jablotron.com, Technical Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the manufacturer after use.
Brauchen Sie Hilfe? Stellen Sie Ihre Frage.
Missbrauch melden von Frage und/oder Antwort
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Jablotron RC-88 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
