Bedienungsanleitung Jablotron SP-02 (Seite 2 von 2) (Englisch)

554866

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

The SP-02 speaker phone 2 / 2 MJV51400

Button

LED

Microphone

The SP-02 speaker phone

The SP-02 half-duplex speaker phone allows a caller (user, an alarm

receiving centre operator etc) to talk and listen-in to the monitored

premises. The device can also be used for emergency calls by

pressing a button. The SP-02 should be connected to a communicator

equipped with a simulated telephone line (e.g. JA-80Y, JA-60GSM) or

to an analogue phone line.

Since the SP-02 only automatically answers phone calls from up to 8

authorized phone numbers, the phone line must support caller

identification (CLIP).It is possible to manually answer calls from

unauthorized phone numbers by pressing a button on the SP-02.

Programming can be locked by a 4-digit user code.

1. Installation

First insert the battery (2x

1.5V AA) – push the

grooved battery cover in

the direction from the

centre to the SP-02’s edge.

Then connect the SP-02 to

the control panel

communicator or to an

analogue PSTN line using

the cable supplied in the

package.

If the batteries do not

have too low a voltage, the

SP-02 is ready for

operation which is

indicated by the green

indicator flashing. If the red

indicator flashes, then the

batteries are discharged

and it is necessary to

replace them (only use quality alkaline batteries).

Mount the device onto the desired location using the holder supplied

in the package.

2. Authorising phone numbers

SP-02 full operation is only possible using authorised tel. numbers –

they must be programmed before the device is used for the first time.

The phone line must support caller identification (CLIP). Jablotron

GSM communicators provide this feature automatically (except for

calls from phones with withheld numbers).

• From any phone, make a call to the SP-02’s phone number (the

number of the line the SP-02 is connected to). As soon as the red

indicator starts flashing press the button to answer the call.

• On your phone key-in programming instructions (sequences)

according to the table below.

• Successful instruction performance is confirmed by 1 beep, an

incorrect instruction is indicated by 4 beeps.

• Terminate the call and test the device functions.

Sequence Function

¿¿

To store a current caller’s phone number to

memory number 1.

¿Dxxxxxxxx¿

Phone number memorization (7 to 22 digits),

D is the phone number memory reference

(1-8).

The SP-02 automatically answers calls from

memorized phone numbers.

¿D¿

To erase a phone number in memory D

¿9xxxx¿

Setting the access code (4 digits) and locking

the SP-02 – first set at least one phone

number!

#xxxx

Unlocking the SP-02, xxxx is a valid access

code

Setting table

Notes:

Programming is only possible when the device is either reset or

unlocked by instruction #xxxx, where xxxx is a valid access code.

When the access code has been set, the SP-02 is automatically

locked. To re-enable programming the SP-02 must first be unlocked.

If locked, the calls from unauthorized phone numbers cannot be

answered by pressing the button on the SP-02.

If there is a fault (e.g. due to a low battery) 10 beeps sound.

Warning: If the SP-02 is locked and no phone number has been

memorized then further communication is impossible. In such a

case, a reset of the SP-02 must be performed. This also applies

when you forget the access code.

3. Listening and calling

The intercom automatically accepts incoming phone calls from up to

8 authorized (preset) phone numbers (see the setting table).

Successful establishment of communication is confirmed to the caller

by a long beep. The green LED is then lit on the SP-02 indicating that

the microphone is switched on (listening in to the premises). An

incoming phone call from an unauthorized phone number is indicated

by a flashing red LED. If the SP-02 is not locked, it is possible to

answer the call by briefly pressing its button.

By briefly pressing the button, the SP-02 will make an emergency

phone call to the phone number stored in the first number memory.

After confirmation by a long beep, the functions are the same as in the

case of an incoming phone call.

The caller’s phone keypad can be used for controlling

communication:

Key /

sequence

Function

Indicated

Switch over: microphone – listening

(toggled) speaker – talking

Green LED

Red LED

Switch on microphone – listening

and switch off speaker

Green LED

Switch on speaker – talking and switch

off microphone

Red LED

0 Terminate the call

Green LED

flashing

#xxxx

Unlock the SP-02

(xxxx is a valid access code)

Beep

Operation table

Notes:

If the SP-02 is not locked, briefly pressing its button has the same

function as key 1 on the phone. So it is also possible to change the

direction (listening/speaking) of communication from the premises end.

Only the caller can terminate the call by pressing key 0 or by hanging

up the phone. The call is also terminated automatically 5 minutes after

the last operation (pressing a key).

During testing it is recommend to keep some distance between the

SP-02 and the phone, otherwise unpleasant audio feedback can be

heard (howl-round).

Pressing the 3, 4, 6, 7, 8 or 9 key will result in communication being

muted. Communication can be restored by pressing any function key

(1,2,5).

4. Reset

A reset can be performed by pressing and holding the button on the

SP-02 while inserting the batteries (hold the button until the red

indicator stops flashing). This resets the device to factory default

settings (all phone numbers erased) and unlocks it.

5. Specification

Power supply 2x alkaline batteries AA 1.5V

Max. number of memorized tel. numbers 8

Analogue interface ETS 300 001, EN 301 437, TBR 21

EMC EN 50130-4, EN 55022

Safety EN 60950-1

Jablotron Ltd. hereby declares that the SP-02 is in

compliance with the essential requirements and other

relevant provisions of Directive 99/5/EC (RTTE). The original

of the conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the manufacturer after use.

Jablotron SP-02 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info