Bedienungsanleitung Jablotron TD-101 (Seite 9 von 12) (Englisch)

554896

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Telephone dialer TD-101 / TD-101W - 16 - MDJ512 10 Telephone dialer TD-101 / TD-101W - 9 - MDJ512 10

9. Trouble shooting

• It is impossible to stop the dialing function with the Ekey even if it is enabled in the installer

mode. Check if either trigger input IN1 nor IN2 is active (especially if you changed the trigger input

logic to a normally closed contact). Additionally, remember that communication with the monitoring

station can not be stopped until it is finished.

• Reaction of the dialer is opposite to what you expect - no reaction when trigger inputs are

activated and the dialer starts to work after inputs are deactivated. In this case the trigger input

logic incorrectly (see item 8.4.).

• Dialer does not work when you press the emergency key

F- check that voice message no. 2

was recorded and that there is a telephone number stored in memory

Mem3 or Mem4. Remember

that the emergency function of the

F key can be disabled in the installer mode (see item 8.11.).

• Dialer does not work after any kind of triggering - check that it is not in the user or installer

mode (green and yellow LEDs must be off). Press the

Ekey to get back to the stand by mode.

Check if the TD-101 is powered correctly (press the

Ekey and you should hear a beep). Check

also, if the voice messages are recorded and that the telephone numbers are stored in

corresponding memories (see chapter 6).

• It is impossible to enter the user or installer mode - it can be entered only if the dialer is not

dialing (red LED must be off). Wait until the dialing is finished or try to stop the dialing with the

Ekey (if stop has been enabled in the installer level).

• You need to temporarily switch the dialer off - for example if the device that controls the dialer

triggers is malfunctioning. In such a case enter the user mode with your user code (the green LED

will be switched on), the TD-101 will be disabled. Remember that the user mode can only be

entered in the moment when the dialer is not calling (red LED must be off). Do not forget to switch

the dialer back to stand by (pressing its

Ekey), after the malfunction is repaired

9.1. Emergency reset

In the event, that you forget your user or installer code (or for some other reason), it is possible to

completely reset all parameters of the TD-101. To do this:

• disconnect the power and wait 1 minute

• reconnect the power (red LED turns on) enter

















(within 10 seconds after

the power is reconnected)

This procedure resets the factory default settings (UC=1234, IC=1010), all phone numbers and remote

controls (TD-101W only) will be deleted. All the optional functions and parameters will be set to the

factory default setting (see table on page 18 for details).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron TD-101 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info