Bedienungsanleitung Jablotron TP-83 (Seite 1 von 2) (Englisch)

554826

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

TP-83 programmable wireless thermostat 1 / 2 MKL51904

The TP-83 programmable wireless indoor thermostat

The TP-83 is a wireless indoor thermostat with a programmable

weekly heating schedule. It is designed for indoor temperature

regulation which balances economy with comfort. The device is

capable of recognizing warm-up persistence characteristics (within 2

days) and will adjust the settings accordingly so that a high level of

operational comfort is achieved. You need not find out how early the

heating should start in order to get to a comfortable temperature at the

desired time. The required timing is configured automatically.

Temperature adjustment can be performed by simply turning the

setting knob.

When combined with an Oasis wireless security system (Jablotron),

the following are possible:

• Switching the heating ON and OFF remotely (by mobile phone,

remote control or Internet).

• Disabling the heating when windows are open.

• Informing the user about heating faults and frost threats (if the

temperature drops below a pre-configured value a warning SMS is

sent).

• Informing on the occurrence of fire (when the temperature is above

a pre-configured value).

Tab

Button

Installation

The TP-83 should be mounted in a dry indoor location. Choose a

mounting location about 1.5 meters above the floor in an area with

good air circulation. Avoid places with draughts, dead air spots and

radiant heat from the sun or appliances. It should not be installed close

to any metal structure or other objects that may obstruct radio signal

transmissions.

1. Release the upper cover by pressing the plastic tab on the bottom

side of the housing

2. Mount the back part on to the desired location.

3. Insert the battery (the polarity is marked on the holder).

4. Close the thermostat.

Enrollment

Install and connect the receiving unit to the heating system. If the

receiving unit was purchased separately then the thermostat must be

enrolled to it – enter enrollment mode on the receiving unit (see its

manual) and either connect the battery to the thermostat or enter menu

M1 (both operations cause an enrollment signal to be sent).

Symbols on the display

Low battery

Heating ON

Time / temperature

display

Manual mode

Time adjustment

Programming

Service menu

Week days

Comfort temperature

Economy temperature

Scheduled time display

Adjustment and programming

All the required parameters can be configured in the adjustment

menu using the knob. The menu is divided into the following parts:

M1 manual temperature-adjustment

M2 setting the economical or comfortable temperature,

time adjustment

M3 weekly programming schedule

M4 service menu

You can enter the menu and scroll through M1 to M4 by pressing and

holding the knob. The desired submenu is selected by releasing the

knob.

Scrolling inside any particular menu M1 to M4 is done by turning the

knob. The currently displayed parameter can be adjusted by pressing

the knob briefly, turning the knob until the desired value is displayed,

and confirming the setting by re-pressing the knob (this will also cause

a return to the menu so that you can configure other parameters

immediately). The adjustment menu is escaped from by pressing the

knob while OK is displayed or automatically after approx. 30 seconds.

1. M1 – manual mode

If set to manual mode, the thermostat performs

fixed temperature regulation regardless of the

weekly schedule. The desired temperature can

be set within the range of t Lo to t Hi. The M1

menu is escaped from by pressing and holding the knob for 2 seconds.

Note: As mentioned above, entering the M1 menu causes an

enrollment signal to be sent.

2. M2 – temperature & time setting

If the M2 menu is entered, turning the knob will scroll through the

Economical temperature (

), Comfortable temperature ( ) and Time

(

) parameters followed by an OK option.

Each parameter can be entered by briefly pressing the knob. When

or is entered the displayed temperature flashes and can be

adjusted by turning the knob (re-pressing the knob confirms the

setting). The Time parameter adjustment is similar but requires three

steps – for the day, hour and minutes.

3. M3 – programming the weekly heating schedule

This mode allows you to program when the thermostat should switch

between Day (

) and Night ( ) operation. The heating schedule can

be programmed either for each day separately or just for working days

or just for the weekend or for all days together.

PRG

SuM o Tu We Th Fr Sa

PRG

SuSa

PRG

M o Tu We Th Fr

PRG

Enter the M3 menu, scroll to the desired option by turning the knob

and enter the schedule programming by briefly pressing the knob (this

erases the current schedule setting).

Schedule programming is done by marking

periods of time for which the Day heating

operation is requested. The marking bar is

shown at the bottom of the display, each

hour can be either marked or unmarked.

You mark or unmark by turning the knob.

The mark/unmark mode is displayed by

symbols, the currently programmed hour is

shown on the display (00 to 23). Switching

between mark/unmark modes is done by

pressing the knob (this applies when turning

clockwise, turning the knob anti-clockwise

always switches to unmark mode).

Turning the knob to the rightmost position

(following hour 23) will display an OK option.

Pressing the knob will then finish

programming.

Jablotron TP-83 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info