Bedienungsanleitung JB systems MIX6usb (Seite 5 von 36) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

756975

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

ENGLISH OPERATION MANUAL

JB SYSTEMS® 3/33 MIX6 USB

In this manual we talk about “line inputs”. This is a global name for inputs with a level between 750mV and

2V. This includes tuners, videos, CD-players, etc.

There are many ways to connect audio equipment to this mixer. Just keep the following remarks in mind:

 Always connect cinch cables in the same way:

o white or black cinch connector  left channel

o red cinch connector  right channel

 Some inputs on the back panel have the possibility to receive a USB, phono or line input. Make sure to

assign the associated switch correctly:

o When you connect a CD-player, Cassette deck, MD-player, tuner, video recorder etc. don’t

forget to put the associated switch to “LINE”.

o When you connect a turntable don’t forget to put the associated switch to “PHONO”.

o When you connect a PC don’t forget to put the associated switch to “USB”.

 Many Turntables have a GND-connection. It is preferable to connect this signal ground to the MIX6 USB.

Use the GND-connections, close to the signal input connectors.

 The record input of an analog recording device can be connected to the record output of the MIX6 USB to

make analog recordings.

FUNCTIONS (FRONT)

1. 3-BAND TONE CONTROL : The frequency can be controlled. In the center position the tone control is

flat. (switched off)

2. MIC VOLUME: Used to adjust the level of the microphone.

3. MIC ON/OFF SWITCH: Used to switch the microphone on/off

4. PEAK LED: Facilitates proper setting of input gain levels. The LED lights up when the signal after the

Gain control (5) reaches 0dB. Warning: the LED should only light up from time to time. If it’s on

continuously, you should turn down the gain level (5) to avoid distortion.

5. GAIN LEVEL: Adjusts the input level on each channel, range goes from zero to maximum. Use this

control to adjust the level at about 0dB (see PeakLED ‘4’).

6. 3-BAND TONE CONTROL : The frequency can be controlled. In the center position the tone control is

flat. (switched off)

7. INPUT SOURCE SELECTOR: Used to select the correct input on each channel: phono, line or USB.

There are also additional input selectors on the back.

Hint: Line, Aux, CD, Tuner, etc… are different names for inputs with almost the same signal levels.

8. CHANNEL FADERS: Used to control the level of each channel. MIX6 USB uses high quality smooth

dual-rail 60mm DJ-faders for maximum reliability.

9. LED VU METER: Accurate level meter. Very important: If you want a nice and clean sound, please pay

attention the VU-meters. Most DJs use this important instrument as a “flashy light effect” . They try to

push the meter constantly to its maximum. Let’s be clear: a good DJ wants a clean, undistorted sound.

Levels over 0dB mean “distortion” so please keep an eye on the meter! 

10. AUX INPUT: can be used to connect an MP3 player, smartphone, etc. to channel 4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JB systems MIX6usb Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info