Bedienungsanleitung JBL Bar 3.1 (Seite 8 von 12) (Englisch)

675574

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Note:

– Make sure that the sound output of your TV is set to “External

speaker”.

– Depending on the remote control, this function may not work

well.

– This function does not operate on LG TV’s magic remote

control.

– This function may not work well when HDMI CEC is ON.

– Some remote control may not operate if you press repeatedly

the volume button.

– If your TV remote control is not supported, follow section 7b and

do IR remote learning.

7b. For other TVs, do IR remote learning

To program the soundbar to respond to your TV remote control,

follow these steps. First, press and hold VOLUME+ and SOURCE

button to enter learning mode.

(1)

LEARNING

>5 s

Then, press POWER button on the soundbar and press POWER

button on the TV remote control

DONE

(2)

SOURCE

Follow the same procedure for VOLUME - and VOLUME +. For

mute, press bloth VOLUME + and VOLUME - button on soundbar

and press MUTE button on TV remote control.

Press and hold VOLUME+ and SOURCE button on soundbar

again and now your soundbar respond to your TV remote control.

8. SYSTEM

1. Auto standby

This soundbar automatically switches to standby after 10

minutes of button inactivity and no audio/video play from a

connected device.

2. Auto wake up

The soundbar is powered on whenever a sound signal is

received. This is most useful when connecting to the TV using

the optical cable, as most HDMI™ ARC connections enable

this feature by default.

3. Set display brightness

Press DIM button on remote control repeatedly to select a

different brightness level of the display panel on this product

4. Apply factory settings

• Reset this soundbar to the default settings programmed at

the factory.

• In any source mode, press and hold VOLUME -, VOLUME+

and SOURCE button on soundbar top panel until text

display shows RESET.

• When the factory settings restore is complete, the product

automatically switches off and restarts.

5. Check Software version

• Press and hold DIM DISPLAY button for 5 seconds in any

source, Hold and press DIM DISPLAY button for 5 seconds,

followed by SOUND MODE and NIGHT MODE button.

• To check subwoofer software version, pls connect

subwoofer to soundbar via a 3.5mm AUX in cable and

follow the above procedure.

6. Software Update

JBL may offer updates for soundbar’s system rmware in the

future. If an update is offered, you can update the rmware by

connecting a USB device with the rmware update stored on

it to the USB port on your soundbar.

Please visit www

.JBL.com or contact JBL call center to

receive more information about downloading update les.

9. PRODUCT SPECIFICATIONS

General

• Total Maximun Power : 450W

• Soundbar Maximum Power : 150W

• Soundbar Standby Power : <0.5W

• Subwoofer Maximum Power : 300W

•

Subwoofer Standby Power : <0.5W

• Soundbar Transducer Size : 6 x 2.25" racetrack drivers

3x1.25"tweeter

• Subwoofer Transducer Size : 10"

•MaxSPL :103db

• Frequency Response : 35Hz to 20KHz

• Operating temperature : 0°C - 45°C

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Bar 3.1 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL Bar 3.1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info