Bedienungsanleitung JBL CINEMA VISION CVSAT50 (Seite 11 von 12) (Englisch)

809537

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

If there is no sound from any

of the speakers:

• Check that receiver/ampli-

fier is on and a source is

playing.

• Check that the powered

subwoofer is plugged in,

and is turned on

(Power

switch åpushed in).

• Check all wires and con-

nections between receiver/

amplifier and speakers.

Make sure all wires are con-

nected. Make sure none of

the speaker wires are

frayed, cut or punctured, or

touching each other.

• Review proper operation of

your receiver/amplifier.

If there is no sound coming

from one speaker:

• Check the “Balance” control

on your receiver/amplifier.

• Check all wires and con-

nections between receiver/

amplifier and speakers.

Make sure all wires are con-

nected. Make sure none of

the speaker wires are

frayed, cut or punctured, or

touching each other.

• In Dolby Digital or DTS

modes, make sure that the

receiver/processor is config-

ured so that the speaker in

question is enabled.

• Turn off all electronics

and switch the speaker in

question with one of the

other speakers that is work-

ing correctly. Turn every-

thing back on, and deter-

mine whether the problem

has followed the speaker, or

has remained in the same

channel. If the problem is

in the same channel, the

source of the problem

is most likely with your

receiver or amplifier, and

you should consult the

owner’s manual for that

product for further informa-

tion. If the problem has fol-

lowed the speaker, consult

your dealer for further assis-

tance or, if that is not possi-

ble, visit www.jbl.com.

If there is no sound from the

center speaker:

• Check all wires and con-

nections between receiver/

amplifier and speaker. Make

sure all wires are connected.

Make sure none of the

speaker wires are frayed,

cut or punctured, or touch-

ing each other.

• If your receiver/processor

is set in Dolby Pro Logic mode,

make sure the center speaker

is not in phantom mode.

• If your receiver/processor

is set in one of the Dolby

Digital or DTS

modes, make

sure the receiver/

processor

is configured so that the

center speaker is enabled.

If the system plays at low

volumes but shuts off as

volume is increased:

• Check all wires and con-

nections between receiver/

amplifier and speakers.

Make sure all wires are con-

nected. Make sure none of

the speaker wires are

frayed, cut or punctured, or

touching each other.

• If more than one pair of

main speakers is being used,

check the minimum imped-

ance requirements of your

receiver/amplifier.

If there is low (or no) bass

output:

• Make sure the connections

to the left and right “Speaker

Inputs” have the correct

polarity (+ and –).

• Make sure the subwoofer

is plugged into an active

electrical outlet

, and is

turned on (Power switch

åpushed in).

• In Dolby Digital or DTS

modes, make sure your

receiver/processor is config-

ured so that the subwoofer

and LFE output are enabled.

• Switch the Phase Switch

çto the opposite position,

and select the position that

results in the most pleasing

bass response.

If there is no sound from

the surround speakers:

• Check all wires and con-

nections between receiver/

amplifier and speakers.

Make sure all wires are con-

nected. Make sure none of

the speaker wires are

frayed, cut or punctured, or

touching each other.

• Review proper operation of

your receiver/amplifier and

its surround sound features.

• Make sure the movie or

TV show you are watching

is recorded in a surround

sound mode. If it is not,

check to see whether your

receiver/amplifier has other

surround modes you may use.

•

In Dolby Digital or DTS

modes, make sure your

receiver/processor is config-

ured so that the surround

speakers are enabled. When

five satellites are in use,

remember to configure your

receiver or processor for

6.1-channel operation, and

when six satellites are in use,

configure your receiver or

processor for 7.1 channels.

• Review the operation of

your DVD player and the

jacket of your DVD to make

sure that the DVD features

the desired Dolby Digital or

DTS mode, and that you

have properly selected that

mode using both the DVD

player’s menu and the DVD

disc’s menu.

TROUBLESHOOTING

CV OM 5/14/04 3:06 PM Page 11

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL CINEMA VISION CVSAT50 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info