Bedienungsanleitung JBL Control ONE AW (Seite 3 von 4) (Englisch)

507346

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

www.jbl.com

English

A. Loosen and remove the molded nut (2) by turning it

counterclockwise. Use the supplied metal bar (5) if necessary

by inserting it in one of the holes on the molded nut (2).

B. Pull the ball/shaft (3) out of the wall bracket (4).

C. Slide the molded nut (2) onto the ball/shaft (3) with threaded

opening facing the ball, and thread on the metal nut (1) all the way

onto the ball/shaft (3), with the nut’s (1) “knurled” surface facing

away from the ball.

D. Screw the ball/shaft (3) into the threaded 1/4"-20 insert (6) on

the back of the speaker cabinet until it is fully seated against the

bottom of the insert. Back out the ball-shaft assembly one half

turn and tighten the nut against the speaker. If the ball and shaft

assembly is not backed out before tightening the nut, performing

Step G below may dislodge the threaded insert in the speaker

housing and permanently damage the speaker.

E. Tighten the “knurled” nut (1) using a crescent wrench until it is firmly

seated against the back of the speaker and has fully locked the ball/

shaft (3) and the speaker cabinet together. Please note that once

this nut is tightened, it may embed some marks on the back of the

speaker where the attachment is made. However, these marks will

be covered by the nut (1).

F. The backup cord (8) is provided as an additional measure to prevent

the fall of the speaker in case the speaker becomes detached from

the wall bracket. One of the two lower screws (9) that attach the

wall bracket (4) to the wall will need to go through the eyelet (11)

at the end of the cord before going through the wall-bracket hole.

Make sure that the screw head is at least 0.36" (approximately 3/8")

or larger in diameter so that it can properly hold the backup cord

eyelet (11).

G. Mount the wall bracket (4) onto a wood stud on the wall, using #10,

minimum 1", panhead wood screws. Make sure that all four screws

are driven into the stud, not drywall.

If the bracket needs to be mounted on drywall, the use of properly

selected and installed wall anchors and screws is essential.

H. Holding the speaker cabinet (7) with both hands, reinsert the ball

portion of the ball/shaft (3) into the wall bracket (4).

I. Hand-tighten the molded nut (2) while positioning the speaker for the

intended orientation.

J. Once the orientation of the speaker is finalized, use the metal bar (5)

in one of the holes on the molded nut (2) and tighten securely.

K. Securely attach the other end (10) of the backup cord (8) to the

Control One AW by engaging it through the bar (12) on the back

speaker, as shown in the illustration.

Please note that while the JBL Control One AW is an all-weather

outdoor loudspeaker, it is not waterproof. The speakers should NOT

be submerged or directly exposed to water, ice, snow or sustained

moisture.

TO LEFT SPEAKER

+–

TO LEFT SPEAKER

+–

CORRECT INCORRECT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL Control ONE AW Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von JBL Control ONE AW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info