Bedienungsanleitung JBL DPS 10 (Seite 6 von 8) (Englisch)

809554

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

– 6 –

Operation

Power

When the unit is plugged in

and no signal is received

for approximately 10 – 15

minutes, the subwoofer will

go into a standby mode until

a signal is present. Due to

JBL’s unique,

high-efficiency

digital-amplifier design,

power consumption is minimal

when the subwoofer is not

receiving a signal.

Low-Pass Control

The Low-Pass control deter-

mines the highest frequency at

which the subwoofer reproduces

sounds. If your main speakers

can comfortably reproduce

some low-frequency sounds,

set this control to a lower

frequency setting, between

50Hz – 100Hz. This will

concentrate the subwoofer’s

efforts on the ultradeep bass

sounds required by today’s

films and music. If you are

using smaller bookshelf

speakers that do not extend to

the lower bass frequencies, set

the low-pass crossover control

to a higher setting, between

120Hz – 180Hz.

High-Pass Control

• If you hooked up your sub-

woofer as shown in Hookup

3 on page 5, you also have

the capability of adjusting

the high-pass frequency.

The High-Pass control

determines the frequency at

which the main speakers

will start reproducing

sounds. If your main speak-

ers can comfortably repro-

duce some low-frequency

sounds, also set this con-

trol to a lower frequency

setting, between 50Hz –

100Hz. This will concen-

trate the subwoofer’s

efforts to the ultradeep

bass sounds, while your

main speakers continue to

reproduce the mid-bass

information. If you are

using smaller bookshelf

Level Control

The subwoofer Level Control,

located on the rear panel,

adjusts the volume of the

subwoofer relative to the rest

of the system. Proper level

adjustment depends on several

variables such as room size,

subwoofer placement, type of

main speakers and listener

position. Adjust the subwoofer

level so that the volume

of the bass information is

pleasing to you.

Crossover Adjustments

speakers that do not extend

the lower bass frequencies,

set the high-pass crossover

control to a higher setting,

between 125Hz – 180Hz.

With this setting, your main

speakers will not have the

burden of reproducing any

low-frequency sounds.

• If you hooked up your sub-

woofer as shown in Hookup

1 on page 3, the high-pass

frequency is fixed at 180Hz.

• If you hooked up your sub-

woofer as shown in Hookup

2 on page 4, there is no

high-pass control. Unless

your receiver/amplifier

incorporates a high-pass

crossover, your main speak-

ers will continue to get a

full-range signal.

Final adjustment and blending

of the low-pass and high-pass

controls may evolve over sev-

eral listening sessions. A good

starting point would be to set

both the low- and high-pass

controls to the same frequency

and adjust from that point.

High

Pass

Phase

60 180

0180

120

90 150

Level

Min Max

Low

Pass

60 180

120

90 150

DPS-10 OM 9/11/98 11:33 AM Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL DPS 10 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info