Bedienungsanleitung JBL STADIUM UB4100 (Seite 6 von 8) (Englisch)

810178

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

• Check that the soundbar’s +12V and GND connections have been properly made.

• Check if the fuse on the +12V wire located near the battery is blown; if so, replace it with an identical fuse.

• Check the fuse located on the soundbar’s control panel. If it’s blown, replace it with an identical fuse.

• If you are using the soundbar’s remote wire for turn-on, check that the wire is properly connected to the

audio system's remote turn-on wire.

No sound (Standby indicator is off)

• Check that the source device’s volume control is not turned all the way down.

• If you’re trying to listen to a Bluetoothdevice or yourvehicle’saudiosystem, make surethat there is no

connection to the soundbar’s 3.5mm audio cable. (A connection to this cable will override all other audio

inputs.)

• If you’re trying to listen to a Bluetooth device, make sure it is paired and connected to the soundbar.

• Check that the soundbar’s Gain control is not turned all the way down (counter-clockwise). See Gain

Control, on page 3, for information about setting the Gain control.

No sound (Standby indicator is on)

• Conﬁrm that the vehicle’s electrical system is supplying between 9V and 16V DC to the soundbar. If the

supply voltage is outside of this range, correct the condition before attempting to use the soundbar.

• If the soundbar has overheated, wait until it has cooled down before attempting to use it again.

• If you have corrected the two above conditions and the soundbar’s Standby indicator is still ﬂashing,

contact your authorized JBL dealer for assistance.

No sound (Standbyindicator is

ﬂashing)

• Check that the soundbar’s Gain control is not turned too low. See Gain Control, on page 3, for

information about setting the Gain control.

Sound is too quiet when listening to

thevehicle’saudiosystem,evenwith

the vehicle audio system’s source unit

volume turned all the way up.

• Check that the distortion is not originating from the source device.

• Check that the soundbar’s Gain control is not turned too high. See Gain Control, on page 3, for

information about setting the Gain control.

Sound is distorted

Problem Causes and Solutions

GOPROMOUNT

Thesoundbar’s bottom bridge plate includes a mountthat lets youeasilyattacha

GoPro™camera. Slide the camera’s foot into the mount clip as shown in the illustration

below. (You can insert the camera into the mount from either direction.)

TROUBLESHOOTING

SPECIFICATION

Product Type : Stereo ampliﬁed mobile soundbar

Frequency Response : 50Hz-20kHz

Maximum SPL : 100dB

Total Ampliﬁer Power : 120Wx2

Power handling : N/A

Driver Complement : 4x 4" Long excursion woofers;

2x 2" Edge-Driven Dome Tweeters

Soundbar Dimension (L x W x H) : 31.5" x 6.12" x 5" (800 x 155.5 x 128mm)

Soundbar Weight : 22.7 lbs (10.3 kg)

Low input level sensitivity : 0.35V – 2V

Hi level input sensitivity : 1.75V – 10V

Aux sensitivity : 0.35V – 1V

BT sensitivity : -9dBFS

BT version : 4.0

BT Transmitter power : 0 – 4dBm

BT transmitter frequency range : 2.402 – 2.480GHz

Proﬁle Support : A2DP V1.3, AVRCP V1.5

SNR @ 1W : >75dB

Channel separation : >60dB

Page4

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JBL STADIUM UB4100 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info