Bedienungsanleitung Jensen JBR550 (Seite 5 von 14) (Englisch)

509205

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

JBR550

INSTALLATION

Before You Begin

1. Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2. Remove Transport Screws

Important Notes

• Before final installation, test the wiring connections to make sure the unit is connected

properly and the system works.

• Use only the parts included with the unit to ensure proper installation. The use of

unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other

modifications to your vehicle.

• Install the unit where it does not interfere with driving and cannot injure passengers if

there is a sudden or emergency stop.

• If the installation angle exceeds 30º from horizontal, the unit may not give optimum

performance.

• Avoid installing the unit where it will be subject to high temperatures from direct sunlight,

hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

DIN Radio Installation

This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In

many cases, a special installation kit will be required to mount the radio to the dashboard.

These kits are available at electronics supply stores and car stereo specialty shops. Always

check the kit application before purchasing to make sure the kit works with your vehicle.

Universal Installation (Using Mounting Sleeve)

1. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal

keys (supplied) to disengage it.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is

not large enough, carefully cut or file as necessary until the sleeve slides easily into the

opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that

there will be sufficient space behind the dashboard for the radio chassis. Connect wires

prior to actually installing the sleeve. Pigtail wiring should take place after hole size is

confirmed. Mount sleeve after wiring.

3. Follow the wiring diagram carefully and make certain all connections of the wiring harness

are properly secured and insulated to insure proper operation of this unit. After completing

the wiring connections, turn the unit on to confirm operation (ignition switch must be “on”).

If unit does not operate, recheck all wiring until the problem is corrected. Once proper

operation is achieved, turn off ignition switch and proceed with final mounting of the

chassis.

4. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve.

With the sleeve fully inserted into the dash opening, bend tabs outward so that the sleeve

is firmly secured to the dashboard.

5. Carefully slide the radio into the mounting sleeve making sure it is right side up until it is

fully seated and the spring clips lock it into place.

6. Attach one end of the perforated mounting strap (supplied) to the screw stud on the rear

of the chassis using the flange nut provided. Fasten the other end of the perforated strap

to a secure part of the dashboard, either above or below the radio using the screw and

flange nut provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with either the perforated strap or

the rubber mounting bushing to prevent damage to the dashboard from the weight of

the radio or improper operation due to vibration.

Kit Installation

1. If your radio requires the use of an installation kit to mount this radio, follow the instruc-

tions included in the kit to attach the radio to the mounting plate supplied with the kit.

2. Wire and test the radio as described.

3. Install the radio/mounting plate assembly to the sub-dash according to the instructions of

the installation kit.

4. Attach the support strap to the radio and dashboard as described above.

5. Replace the dashboard trim panel.

SECURE THIS END TO

SUB-DASH STRUCTURE

PERFORATED SUPPORT STRAP

MOUNTING SURFACE OPENING

NOTE: IF OPENING DOES NOT EXIST,

USE MOUNTING SLEEVE AS A TEMPLATE

AND CUT OPENING. FILE EDGES TO FIT

IF NECESSARY. DO NOT OVER FILE.

SECURE THIS END TO

REAR OF RADIO

DIN MOUNTING SLEEVE

LOCKING TABS

REAR SUPPORT SCREW

REMOVAL KEYS

MOUNTING

SURFACE

MOUNTING

SLEEVE

BEND TABS

BOTTOM TAB

BEND DOWNWARD 90°

MOUNTING TAB DETAILS

CUTAWAY VIEW OF

MOUNTING SURFACE

SIDE VIEW

TOP TAB BEND

UPWARD 90°

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jensen JBR550 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info