Bedienungsanleitung Jensen JCD2010 (Seite 3 von 10) (Englisch)

509192

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

JCD2010

INSTALLATION

Before You Begin

1. Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2. Remove Transport Screws

Important Notes

• Before final installation, test the wiring connections to make sure the unit is connected

properly and the system works.

• Use only the parts included with the unit to ensure proper installation. The use of

unauthorized parts can cause malfunctions.

• Consult with your nearest dealer if installation requires the drilling of holes or other

modifications to your vehicle.

• Install the unit where it does not interfere with driving and cannot injure passengers if

there is a sudden or emergency stop.

• If the installation angle exceeds 30º from horizontal, the unit might not give optimum

performance.

• This unit is not waterproof and is intended for interior mounting applications only.

Exterior mounting of the unit requires use of an ASA approved marine housing.

• Avoid installing the unit where it will be subject to high temperatures from direct sunlight,

hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

DIN Front/Rear Mount

This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear”

(DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis)

mount. For details, refer to installation methods A and B.

DIN Front Mount (Method A)

1. Slide the mounting sleeve off of the chas-

sis if it has not already been removed. If it

is locked into position, use the removal

keys (supplied) to disengage it. The

removal keys are depicted in “Removing

the Unit” on page 3.

2. Check the dashboard opening size by

sliding the mounting sleeve into it. If the

opening is not large enough, carefully cut

or file as necessary until the sleeve easily

slides into the opening. Do not force the

sleeve into the opening or cause it to bend

or bow. Check that there will be sufficient space behind the dashboard for the radio

chassis.

3. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.

With the sleeve fully inserted into the dashboard opening, bend as many of the tabs

outward as necessary to firmly secure the sleeve to the dashboard.

4. Place the radio in front of the dashboard opening so the wiring can be brought through the

mounting sleeve.

5. Follow the wiring diagram carefully and make certain all connections are secure and

insulated with crimp connectors or electrical tape to ensure proper operation.

6. After completing the wiring connections, turn the unit on to confirm operation (vehicle

ignition switch must be on). If the unit does not operate, recheck all wiring until the

problem is corrected. Once proper operation is achieved, turn the ignition switch off and

proceed with final mounting of the chassis.

7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is

fully seated and the spring clips lock it into place.

8. Attach one end of the

perforated support

strap (supplied) to the

screw stud on the rear

of the chassis using the

hex nut and spring

washer provided.

Fasten the other end of

the perforated strap to a

secure part of the

dashboard either above

or below the radio using

the screw and plain

washer provided. Bend

the strap, as necessary,

to position it.

CAUTION: The rear of the radio must be supported with the strap to prevent damage to

the dashboard from the weight of the radio or improper operation due to vibration.

9. Test radio operation by referring to the operating instructions for the unit.

Removing the Unit

To remove the radio after installation:

1. Insert fingers into the groove in the front of

frame and pull out to remove the frame.

(When re-attaching the frame, point the

side with a groove downwards and re-

attach.)

2. Insert the removal keys straight back until

they click, and then pull the radio out. If

removal keys are inserted at an angle,

they will not lock properly to release the

unit.

Trim Plate Installation

Push the trim plate against the chassis until it is

fitted.

182

Dashboard

Bend Tabs

Screw Stud

Dashboard

Machine Screw (5 x 25mm)

Hex Nut (5mm)

Rubber Bushing

Screw Stud

Support Strap

Dashboard

Removal Key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jensen JCD2010 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info