166238
3
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
3
®
XA4100
Supplies and Tools Needed
Supplies:
Speaker wire (12 gauge for subwoofers, 16-18
gauge for other speakers)
Sheet metal type screws for mounting amplifier
Electrical tape
Solderless crimp connectors
1/2" thick plywood or particle board to mount
amplifier on
Tools:
Flat and Phillips screwdrivers
Wire cutters
Wire strippers
Cordless or standard electric drill and drill bit set
Crimping tool (if using solderless crimp
connectors)
12-volt test light or digital multimeter
Wire brush or scraper (to remove paint for a
good ground connection to vehicle)
Soldering iron and rosin core solder (if you're
going to solder your connections)
Amplifier Installation Kit:
You will need an amplifier installation kit to install
your amp properly because it contains all the
wire and connectors that you will need to hook
up your new amp right the first time. If you want
to purchase these items separately you will need
the following:
20-25 feet of 8 gauge wire
50 amp fuse or circuit breaker (to be hooked up
at the battery)
20 feet of 18 gauge wire for the remote turn-on/
power antenna lead
RCA cable (for signal input from radio)
20 feet for trunk installation
12 feet for under-seat installation
Two 8 gauge ring terminals (one for the battery
connection and the other for the ground connec-
tion at the amp). You may need two additional
ring terminals if you are using a circuit breaker at
the battery.
Two 8 gauge barrel connectors (you may need
these depending on what type of fuse holder you
have)
Two 8 gauge spade terminals (to hook up power
at the amp)
Eight 12 gauge spade terminals for subwoofers
or 16-18 gauge spade terminals for other
speaker connections to amp
One 18 gauge spade terminal for remote turn-on/
power antenna lead
Routing Wires
Professional Tip
Bigger is better
Stereo installation dealers sell extra thick
power and speaker wires to ensure best
sound. Look for 8 gauge power wire, espe-
cially if you have several amplifiers.
Speakers
Amplifier
Battery
Connector
Fuse or
Circuit
Breaker
Battery
Power Wire
(8 gauge
wire or
larger)
Power Antenna
Turn-on Wire
(18 gauge wire)
RCA Cables
Ground Screw
Drill 1/8" hole in
chassis sheet metal
Use the same ground if
using multiple amplifiers
Grommet
To prevent
damage to
power wire
Receiver
5313Eamp.p65 4/10/99, 7:05 PM3
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jensen xa 4100 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info