Bedienungsanleitung JL Audio 1D (Seite 6 von 37) (Englisch)

700471

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

10 JL Audio JX250/1 • JX500/1D • JX1000/1D 11

ENGLISH

STATUS INDICATOR LIGHTS /

PROTECTION CIRCUITRY

There are two status indicator lights on the

amplifier’s control panel. These are as follows:

1) “Power” (Green): Located at the far left of the

amplifier’s control panel, this LED lights to

indicate that the amplifier is turned on and

operating normally.

2) “Protect” (Red): Indicates that the amplifier

protection circuitry has been activated

to prevent product failure due to thermal

overload, short-circuit or a dangerously

low impedance connected to the amplifier

outputs. Connecting the speaker output to

an impedance lower than 2 ohms will cause

this protection mode to activate. When this

protection mode is activated, the amplifier will

shut down to protect its circuitry. When the

problem is corrected, the amplifier will return

to normal operation and the “Protect” LED

will shut off.

SERVICING YOUR AMPLIFIER

If your amplifier fails or malfunctions, please

return it to your authorized JL Audio dealer so

that it may be sent in to JL Audio for service.

There are no user serviceable parts or fuses inside

the amplifier. The unique nature of the circuitry

in the JL Audio amplifiers requires specifically

trained service personnel. Do not attempt

to service the amplifier yourself or through

unauthorized repair facilities. This will not only

void the warranty, but may result in the creation

of more problems within the amplifier.

If you have any questions about the installation or

setup of the amplifier not covered in this manual,

please contact your dealer or technical support.

JL Audio Technical Support:

(954) 443-1100

9:00 AM – 5:30 PM (Eastern Time Zone)

Monday - Friday

SPEAKER OUTPUT

Subwoofer connection to the JX monoblock

is straightforward and takes place at the

far right of the power/speaker connection

panel. Two positive (“+”) connections and

two negative (“–”) connections are available

via a connector labeled “Speaker Output

(Mono)”. The dual connections allow for two

separate speaker wire runs to be parallel-

connected to the amplifier’s mono output.

IMPORTANT!

Speaker loads below 2Ω nominal are not

recommended and will cause the amplifier to

enter into a protection mode.

Do not chassis ground any speakers connected

to this or any other JL Audio amplifier. Doing so

will cause the amplifier to go into protection.

To connect the speaker wires to the amplifier,

strip 1/2-inch (12 mm) of insulation from each

speaker wire and insert them into their

appropriate connector (observing correct

polarity). Then, tighten each connector using the

supplied 2.5 mm hex wrench.

IMPORTANT!

Do NOT attempt to “bridge” two JX

monoblocks together or combine their output

to a single load in any manner. Doing so will

damage the amplifier(s).

IMPORTANT!

Before reconnecting the battery ground and

turning the system on, verify that all control

settings on the amplifier are set according to

the needs of the system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio 1D Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info