Bedienungsanleitung JL Audio 1i (Seite 2 von 2) (Englisch)

700430

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Limited Warranty – Amplifiers (USA)

JL Audio warrants this product to be free of defects in materials and workmanship

for a period of two (2) years from the original date of purchase. This warranty is

not transferable and applies only to the original purchaser from an authorized

JLAudio dealer. Should service be necessary under this warranty for any reason due

to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or

replace the defective product with new or remanufactured product at no charge.

Damage caused by the following is not covered under warranty: accident, misuse,

abuse, product modification or neglect, failure to follow installation instructions,

unauthorized repair attempts, misrepresentations by the seller. This warranty does

not cover incidental or consequential damages and does not cover the cost of

removing or reinstalling the unit(s). Cosmetic damage due to accident or normal

wear and tear is not covered under warranty.

Warranty is void if the product’s serial number has been removed or defaced.

Any applicable implied warranties are limited in duration to the period of the

express warranty as provided herein beginning with the date of the original

purchase at retail, and no warranties, whether express or implied, shall apply to

this product thereafter. Some states do not allow limitations on implied warranties,

therefore these exclusions may not apply to you. This warranty gives you specific

legal rights, and you may also have other rights, which vary from state to state.

If you need service on your JL AUDIO product:

All warranty returns should be sent to JL Audio ’s Amplifier Service Facility

freight-prepaid through an authorized JL Audio dealer and must be accompanied

by proof of purchase (a copy of the original sales receipt). Direct returns from

consumers or non-authorized dealers will be refused unless specifically authorized

by JL Audio with a valid return authorization number. Warranty expiration on

products returned without proof of purchase will be determined from the

manufacturing date code. Coverage may be invalidated as this date is previous

to purchase date. Non-defective items received will be returned freight-collect.

Customer is responsible for shipping charges and insurance in sending the

product to JL Audio. Freight damage on returns is not covered under warranty.

For Service Information in the U.S.A. please call

JL Audio Customer Service:

(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)

JL Audio, Inc.

10369 North Commerce Pkwy. Miramar, FL 33025

(Do not send product for repair to this address)

International Warranties:

Products purchased outside the United States of America are covered

only by that country’s distributor and not by JL Audio, Inc.

V X10 0 0/1i _ MA N _ 0 41118

Connections

Power Connector

Connection Wire Capacity Description

+12 VDC (+) 2 AWG Positive (+12V) Power Connection to Battery

Ground (–) 2 AWG Negative (GND) Chassis Ground Connection

Remote 18 to 10 AWG Positive (+12V) Remote Turn-On Input from Source Unit

Analog Input Harness

Label

Plug/Wire

Color

Description

Input 1 White RCA Channel 1 Signal Input

Input 2 Red RCA Channel 2 Signal Input

Pre-Out Left White RCA Preamp Signal Output 1

Pre-Out Right Red RCA Preamp Signal Output 2

Remote Blue Positive (+12V) Turn-On Output (475 mA limit)

Valet Green Negative (GND) Ground Input (activates the Valet Mode Preset)

Subwoofer Output Connector

Connection Wire Capacity Description

SUB + 14 to 10 AWG (+) Positive Subwoofer Output

SUB – 14 to 10 AWG (–) Negative Subwoofer Output

Data Connections

Label Type Description/Use

JLid-COMM RJ45 Jack Optional accessory connections (VXi-BTC, VXi-HUB, etc)

JLid-CTRL RJ45 Jack Optional DRC (Digital Remote Controller) connection

USB USB A/B Port Computer connection to congure TüN™ Software Interface

DIGITAL-In S/PDIF Port 2-channel, optical (Toslink) digital input

DIGITAL-Out S/PDIF Port 2-channel, optical (Toslink) digital output

SD + Reset

Reset Buttons Multifunction use (Reboot/Reset/Device Firmware Update mode)

Micro SD Slot Used for future expansion

Specifications

Amplier Specications

Amplier Topology 2nd-Gen NexD™ High Speed Class D

Power Supply Type Unregulated MOSFET Switching

Operating Voltage 10 - 15V DC

Min. Copper Power/GND Wire 4 AWG

Recommended Fuse 80 A

Standby Current Draw 3.6 mA

Input Voltage Range 200 mV - 16 V RMS

Rated RMS Power @ 14.4V,

<1% THD+N

600W x 1

@ 4 Ω

800W x 1

@ 3 Ω

1000W x 1

@ 2 Ω

Rated RMS Power @ 12.5V,

<1% THD+N

500W x 1

@ 4 Ω

650W x 1

@ 3 Ω

800W x 1

@ 2 Ω

Frequency Response 12 Hz - 500 Hz (+0, -1dB)

Analog

Inputs

S/N Ratio,

(A-weighted, 20 kHz

noise bandwidth)

87 dB (Referred to rated power),

60 dB (Referred to 1 W)

Digital

Input

S/N Ratio,

(A-weighted, 20 kHz

noise bandwidth)

87 dB (Referred to rated power),

56 dB (Referred to 1 W)

Damping Factor >400 / 50 Hz @ 4 Ω, >300 / 50 Hz @ 2 Ω

DSP Specications

Processor AKM AK7738, processing at 24 bit/96 kHz

Analog

Inputs

Type Line-Level, Dierential-Balanced

Number of Channels 2, via harness-mounted female RCA jacks

Digital

Input

Type S/PDIF Optical via chassis-mounted Toslink port

Bit Depth/Sample Rate

Up to 24 bit/192 kHz

Analog

Outputs

Type 2 Line-Level, via harness-mounted female RCA jacks

Max Output Level 4 V RMS

Digital

Output

Type S/PDIF Optical via chassis-mounted Toslink port

Bit Depth/Sample Rate 24 bit/96 kHz

Dimensions

L x W x H 11.32 in x 6.62 in x 2.12 in / 287 mm x 168 mm x 54 mm

What is TüN?

TüN™ is software that you use to configure, tune and control your VXi

amplifier, and other JL Audio DSP products. TüN™ automatically recognizes

what it is connected to, and allows you to make adjustments with a

clear interface specifically set up for that product. TüN™ is available for

download for free in a variety of applications, for computers and most

handheld devices. For more information, visit: jlaudio.com/tun

For Windows® PC or Mac® computers, TüN™ connects via

USB and offers complete control and command of the entire

VXi feature set from the comfort of your desk or driver’s seat.

Software also runs in demo mode, without connected amplifiers,

for offline setup or demo purposes. Test drive it for free!

For iPad or Android tablets. Enjoy the full-featured TüN™ software

experience on your tablet, with the freedom of a wireless connection

via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.

Wireless connection and streamlined options, for fast and simple

amplifier setup. Download TüN™ Express for iPhone, iPad and Android

phones & tablets. Requires VXi-BTC Bluetooth® Communicator.

+12 VDC - Positive (+12V) Battery Connection

Ground - Negative (–) Ground Connection

Remote - Positive (+12V) Turn-On Input From Source Unit

JLid-COMM - Optional Network Hub or

Bluetooth® Communicator Connection (Sold Separately)

JLid-CTRL - Optional Digital Remote Controller

(DRC) Connection (Sold Separately)

Wiring Diagram - VX1000/1i

Input 2 - Ch. 2 Input

Input 1 - Ch. 1 Input

Pre-Out Right - Analog Preamp Output

Pre-Out Left - Analog Preamp Output

Remote - Turn-On Output (+12V)

Valet - Valet Preset Toggle (–)

SUB - To Subwoofer(s): (+ and –)

DIGITAL-In - From Optical Digital (S/PDIF) Source

DIGITAL-Out -

To Optical Digital (S/PDIF) Input on Next Device

USB A/B Cable -

To Computer with TüN™ software installed

Included

Not Included

SUB

–

Standard CAT5 Network Cables

Optical Audio Cables

ANALOG INPUTS / PRE-OUTS

LED Status/Condition Reporting

LEDs located on the chassis top and connection panel are used to

communicate amplier status and condition. Refer to the table below for

the location and meaning for each behavior.

LED / Location Behavior Status/Condition›

LED Ring /

Amplier Top

Flashing Blue Critical Voltage

Flashing Red Critical Temperature

Flashing Yellow Excessive Current

Upper Left LED /

JLid-COMM Port

and

JLid-CTRL Port

Green Detecting JLid™ Device

Blue JLid™ Connection Success

Yellow Invalid JLid™ Device

Flashing Red Excessive Current

Upper Right LED /

JLid-COMM Port

Flashing Red

Critical Voltage/Temperature

Excessive Remote Output Current

Upper Right LED /

JLid-CTRL Port

Green Active TüN™ Connection

JL Audio 1i Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info