701305
5
Zoom out
Zoom in
Vorherige Seite
1/11
Nächste Seite
SPEAKER OUTPUTS
The A6450’s speaker outputs are designed to
accept 16 AWG - 8 AWG wire.
Each pair of the A6450’s channels are designed to
deliver power into speaker loads equal to or greater
than 2 ohms when using a “stereo” configuration
and speaker loads equal to or greater than 4 ohms
when using a “bridged” configuration.
Speaker loads below 2 ohms nominal per
channel are not recommended and may cause
the amplifier to initiate a protection mode
which reduces power output.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from a
single channel. The A6450 has been designed for
bridging of its channel pairs without the need for
input inversion adaptors.
To bridge a pair of channels, use the “Left +
and Right – speaker connectors only (the
Left and Right + remain unused). When
bridged, each channel will deliver optimum
power into a 4 ohm load.
When a pair of channels are bridged, they
will deliver 150W x 1 into a 4 ohm load or
90W x 1 into an 8 ohm load. Operating a
pair of bridged channels into a load lower
than 4 ohms is not recommended.
Because a bridged pair of channels requires
that both channels receive input, you need to
connect both left and right inputs to the source
unit. Connection of only one input will result in
reduced power output, increased distortion and
can cause the amplifier to overheat.
Do not do this!
When a pair of the A6450’s channels are
operating in bridged mode, the output will be in
mono (only one channel). This mono channel
can contain right channel only information,
left channel only information or the sum of
the information from both the right and left
channels. In order to achieve one of these options,
configure the inputs to that pair of channels in
one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only
or right-only signal to a pair of the A6450’s
channels, use a “Y-Adaptor” to split the single
channel signal into both left and right RCA
inputs. This option is useful when using a pair
of the A6450’s channels to drive left channel
speakers only and the other pair of the A6450’s
channels to drive right channel speakers only.
2) Left + Right Channel Information: When
bridged and fed by a stereo input, a pair of the
A6450s channels will automatically combine
the left and right channels into a summed
mono (left + right) channel. This option
is useful when using a pair of the A6450s
channels to drive a subwoofer system or a
summed mono center channel.
JL AUDIO A6450 9
“LP” (Low-Pass): Configures the filter to
attenuate frequencies above the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of subwoofer(s) to one
or more of the A6450’s channel pairs in a
bi-amplified system.
“HP” (High-Pass): Configures the filter to
attenuate frequencies below the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of component speakers to
one or more of the A6450’s channel pairs in a
bi-amplified system.
2) Filter Freq. (Hz)” The filter frequency
markings surrounding this rotary control
are for reference purposes and are generally
accurate to within 1/3 octave or better. If you
would like to select the filter cutoff frequency
with a higher level of precision, consult the
chart in Appendix B (page 15).
Tuning Hi nt: If you are using the A6450 to drive
a subwoofer system (“LP mode), a component
satellite speaker system (“HP mode) or both,
80 Hz is a good baselineFilter Freq. (Hz)
setting. After properly adjusting the “Input
Sens., as outlined in Appendix A (page 14), you
can fine tune the “Filter Freq. (Hz)” control to
achieve the desired system frequency response.
BASS BOOST CONTROLS
1) “Bass Boost: Found in the “Channel 5 & 6
Controls section, this switch allows the user
to activate a 6 dB boost centered at 48 Hz
for channels 5&6. When the “Bass Boost” is
activated, the inputs to “CH 5 (Left)” and “CH
6 (Right)” are summed to create a mono signal.
TheFilter Mode switch in theChannel
5 & 6 Controls section must be in the “LP
position for the bass boost to be functional.
2) “Remote Bass Port”: This port allows you to
connect an optional remote boost knob (sold
separately as JL Audio Model RBC-1) that can
be mounted in the front of the vehicle. With
the RBC-1 connected, the boost is no longer
limited to 0 or +6 dB, allowing a variable
range of 0 to +12 dB of boost to be selected.
8 JL AUDIO A6450
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JL Audio A6450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info