Bedienungsanleitung JL Audio C1-570x (Seite 4 von 8) (Englisch)

701256

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

4 | JL Audio - C1-570x Owner’s Manual

WARNING

Double check the clearance for both speakers

before proceeding. Many cars are different from

one side to the other!

Speaker Installation in Factory Locations:

Your new speakers have been designed to

install, without modifications, into most vehicles

with OEM speaker locations that accept a 5 x

7-inch (125 x 180 mm) speaker. The speaker

frames also have slotted mounting holes suitable

for installation into factory 6 x 8-inch speaker

locations. Many factory 5 x 7-inch speakers use

four mounting screws, which will line up with

the mounting holes on your C1-570x speakers.

Spacer adaptor rings are included to fit, bottom-

mount applications, if needed. Each spacer ring

can be placed on the front of the mounting

flange, in between the speaker and mounting

panel, as shown in Diagram A (page 5).

It is absolutely vital that the speaker frame

fits into the mounting hole cleanly. This must

be checked prior to tightening the screws. Never

force the frame into a hole that is too small, and

do not attempt to tighten the speaker onto an

uneven surface. This will damage your speakers.

The speaker should fit so that air does not leak

around the mounting flange. Air leaks will cause

a severe degradation in sound quality. Seal any air

leaks with an automotive-grade sealant material.

WARNING

Hand-tighten the screws evenly in a criss-cross

pattern to avoid bending the speaker frame or

stripping the mounting screws.

INSTALLATION OVERVIEW

C1 speakers are designed for installation into

OEM speaker locations, mounted behind factory

panels/grilles. Depending on the equipment used

or design of your audio system, you may use the

factory speaker wires or run new speaker wires to

each speaker location. You will also need to run new

speaker wires if you elect to mount your speakers in

custom locations. Select the wiring method that is

appropriate for your audio system and equipment.

If you are unsure about this or any steps in the

installation process, please contact your JL Audio

dealer for installation help

Speaker Wiring:

If you will be using the factory speaker wires, it may

be necessary to change the terminations. This may

be accomplished by using an adaptor plug or simply

by cutting the factory connector off and using the

supplied crimp connectors to terminate the speaker

wires. The larger connector is for the positive terminal

and the smaller connector is for the negative terminal

of each C1-570x.

If you choose to run new speaker wires, protect all

wiring from sharp edges by carefully routing them,

securing them and using grommets and loom where

appropriate. If you are running wires into a door, use

existing factory wiring boots whenever possible. If

you are drilling new holes, file their edges and install

rubber grommets into each hole. Wires running into

car doors should be covered with a protective, flexible

PVC sleeve. Make sure that the wires will clear door

hinges and other structures in the door.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio C1-570x Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info