Bedienungsanleitung JL Audio MMR-20 (Seite 1 von 2) (Englisch)

700486

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

MediaMaster® Wired Remote Controller

Product Description

The MMR-20 is a water-resistant

(IP67 rated), wired remote controller designed

to add auxiliary control functionality to

MediaMaster® source units. Depending on

your system layout, you may add up to three

MMR-20 remote controllers to a single source

unit. Each MMR-20 can be connected up to

75 ft. (22.8 m) away from its source unit. A

Y-splitter and remote extension cables are

sold separately and available in different

lengths to suit different mounting locations.

What’s Included

(1) MMR-20 wired remote controller

(1) Standard gasket

(1) Lipped gasket (optional)

(2) Stainless steel threaded studs

(4) Stainless steel nuts (7 mm)

(4) Stainless steel washers

(1) Aluminum C-bracket

(1) User Manual

Safety Considerations

• While this product is designed to be water-

resistant, it should never be submerged

under water or subjected to high-pressure

water spray.

• Do not mount in areas of extreme heat.

• Ensure this product is securely installed so

that it does not come loose in the event

of a collision/sudden jolt or as a result

or repeated vibrations during normal

operation.

• Check before drilling to make sure that you

will not be drilling into a fuel tank, gas/brake

line, wiring harness, or other vital system.

• Secure all wiring as needed, using cable

ties or wire clamps to protect them from

moving parts and sharp edges.

Mounting & Installation

A 2-inch (50 mm) hole is required for

mounting, along with adequate rear access

to secure/tighten the hardware. The included

hardware accommodates installations in flat

panels up to 1.5-inches (38 mm) thick.

The C-bracket is designed with break lines

to allow adjustment for different mounting

panel thicknesses. To remove a leg section,

use pliers and bend back and forth at

a break line to separate. Be mindful of

resultant sharp edges and file if necessary.

Make sure to carefully plan the routing of

the remote’s connection cables prior to

cutting or drilling any panels.

1. Select an appropriate mounting location

and cut a 2-inch (50 mm) hole using an

appropriate tool/hole saw.

2. Place the standard gasket onto the rear

of the remote. For retrofit installations,

the lipped gasket may be used where an

existing mounting hole is slightly larger

than 2-inches.

3. Apply thread sealer (not included) onto

the threaded studs and insert them into

the inserts at the rear of the MMR-20, and

hand tighten.

4. Install a nut and washer near the middle

section of each stud (see diagram) and

place the MMR-20 into the mounting hole.

5. From behind the mounting panel, slide

the C-bracket onto the threaded studs and

press it forward, towards the MMR-20

6. Apply thread sealer and adjust the position

of the previously installed nuts and

washers to support the C-bracket while

still allowing the legs to of the C-bracket

to press against the rear of the mounting

panel.

7. Apply thread sealer and install a remaining

nut and washer onto each stud. Tighten

the C-bracket to the mounting panel.

Lipped

Gasket

(optional)

Standard

Gasket

(required)

Remove

leg sections

as neeeded

MMR-20

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

JL Audio MMR-20 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info