Bedienungsanleitung JL Audio MMR-40 (Seite 2 von 2) (Englisch)

700485

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Mounting & Installation

The diagram below shows a typical

mounting procedure into a fiberglass panel.

A mounting template is included to aid

in measuring and marking the mounting

surface before cutting or drilling.

Make sure to carefully plan the routing of

the remote’s connection cables prior to

cutting or drilling any panels.

1. Press along the perforation to remove the

center section of the mounting template.

(Discard the center section.) The template

can be used to verify there is sufficient flat

surface area for mounting and as a guide

for cutting the opening. Tape the template

to the mounting location and mark the

surface for cutting the opening and drilling

pilot holes.

2. Use a jigsaw or rotary tool to cut an

opening in the mounting surface. If

necessary, use a file or sandpaper to

adjust the opening for proper fitment and

smooth the edges.

3. Place the MMR-40 into the opening and

check that the mounting holes remain

aligned with the pilot hole marks taken

from the template. If not, adjust and mark

new holes as necessary.

MMR40-MAN 080918 • Printed in China

2-Year Limited Warranty (U.S.A.)

Visit www.jlaudio.com for warranty details.

For Service Information in the U.S.A. please call JL Audio customer service:

(954) 443-1100 during normal business hours (Eastern Time)

JL Audio, Inc • 10369 N Commerce Parkway, Miramar, FL 33025

International Warranties:

Products purchased outside the United States of America are covered only by that

country’s distributor and not by JL Audio, Inc.

Connections

The MMR-40 is equipped with a NMEA 2000®

Micro-C connector and can connect to a

host MediaMaster® source unit in the two

methods shown below. The USB connector is

used for future software updates.

• Direct interface with a vessel’s NMEA 2000®

network using applicable NMEA 2000®

cables and connectors (not included).

• Direct connection of one MMR-40 with

one host MediaMaster® source unit using

JL AUDIO® MMC-PN2K powered network

cables (sold separately) to simulate an

isolated, stand-alone NMEA 2000® network.

Note: JL Audio® Powered Network Cables support a maximum of two NMEA

2000® devices. For systems with additional NMEA 2000® devices, a genuine

NMEA 2000® network must be assembled, which does not support JL Audio®

Powered Network Cables.

4. Remove the MMR-40 and drill four (4) pilot

holes in the mounting surface at the pilot

hole marks.

5. Peel the adhesive backing from the

mounting gasket and affix to the rear of

the bezel. Connect all wiring and place the

MMR-40 into the opening.

6. Secure the MMR-40 using the four (4)

mounting screws. Press the trim ring onto

the front of the MMR-40.

SOURCE UNIT

COMPATIBLE

MULTI-FUNCTION

DISPLAY

To applicable

network

components

(not shown)

To applicable

network

components

(not shown)

Use the MMR-40 for MediaMaster® remote command functionality

via your vessel’s existing NMEA 2000® network (cables sold separately).

Use the MMR-40 for MediaMaster® remote command functionality

via JL Audio® Powered Network Cables

(MMC-PN2K-6 & MMC-PN2K-25, sold separately).

SOURCE UNIT

Use JL Audio® Powered Network Cables for MediaMaster® remote command functionality

via MMR-40 NMEA 2000® Network Controller.

[

GROUND

]

[

SHIELD

]

[

+12V

]

[

GROUND

]

[

SHIELD

]

[

+12V

]

SOURCE UNIT

[

GROUND

]

[

SHIELD

]

[

+12V

]

Note: JL Audio® Powered Network Cables support a maximum of two NMEA 2000® devices.

For systems with additional NMEA 2000® devices, a genuine NMEA 2000® network

must be assembled, which does not support JL Audio® Powered Network Cables.