28356
40
Zoom out
Zoom in
Vorherige Seite
1/148
Nächste Seite
Section 2 Installation
39
Note:
There may be 2 positions where the targets are strong. Select the one that
has the larger value of “TUNE PRESET”.
•Push the
Joystick
to save and exit.
Relative BEARING alignment
This adjustment should be performed after installation or a master
reset to avoid incorrect bearing readouts and picture orientation. Using
the 1.5 NM range, identify a small target such as a boat or buoy that
can be seen both visually and on the radar. Point the boat so the target
is visually dead ahead. If the radar target does not also show on the
heading line proceed with this adjustment. In the Radar Adjust menu
select BEARING by
Joystick
up/down, moving the hiliter, and
selecting by pushing the
Joystick
. Move the dashed Electronic Bearing
Line (EBL) by
Joystick
left/right to bisect the radar target that should
be dead ahead. Push the
Joystick
once. Move the EBL to dead ahead
and push the
Joystick
again to rotate the picture by the offset just
indicated.
DISPLAY TIMING
This step must be performed. Failure to perform this step may
result in incorrect target distance reading.
•Set the range scale to 0.25 NM.
• Locate a pier, a jetty, a bridge (close to water line) or any other straight
object. Position the vessel so that it appears on the display. It does not
matter which way you are facing.
•In the RADAR ADJUST menu, select DISPLAY TIMING by
Joystick
up/down, and push
Joystick
.
The DISPLAY TIMING pop-up menu is displayed.
•If the bridge, pier or jetty does not appear to be in a straight line on
the display, then the DISPLAY TIMING needs to be adjusted.
•Use the
Joystick
right/left to adjust the timing and make the object
appear straight on the display.
•Press
Joystick
when done.
STC PRESET
This step must be performed. Failure to perform this step may
result in incorrect sea clutter suppressing.
•Set the range scale to 6 NM.
•Turn IR off, STC to maximum, and set gain to maximum.
•In the RADAR ADJUST menu, select STC PRESET by
Joystick
up/down, and push
Joystick
.
The STC PRESET pop-up menu is displayed.
•Use the
Joystick
to remove all background noise from 0-3 NM.
•Press
Joystick
when done.
40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für JRC Radar1800 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info